Install Instructions for Kat's Block Heater KH11409

Question

Question:

Hello, As per this aswer for that question: Where to Install Kats Custom Engine Block Heater on 2015 Mazda CX-5 he said that he added a link to the directions: I did add a diagram that should be helpful although as of right now we have not yet had a chance to made a video showing the Kats Custom Engine Block Heater # KH11409 being installed on a 2015 Mazda CX-5. After checking out the instructions for this block heater I was able to find that you will need to this Frost-Plug heater into the LRinch position of your Mazdas engine, as you can see in the diagram. All you need to do is remove that frost plug and the heater Ive also added a link to the directions for you to check out. Where is that link hes talking about? Thanks!!

asked by: Martin G

0

Expert Reply:

I attached a picture to this page that shows the install instructions for the Kat's Block Heater # KH11409 that you referenced.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Kat's block heater you need for your 2012 Ford F-150 is a cartridge style heater part #KH11815 which installs in the cartridge on the motor in the "right front" position which is the passenger side of the motor closest to front of…

view full answer...

Answer 2

For your 2011 Ford Flex with the 3.5L non-ecoboost engine we only have the Kat's Heaters Custom Engine Block Heater #KH11409 which is a frost plug style connection. The Cartrige Heater #KH11815 you found is only for the ecoboost engines. The…

view full answer...

Answer 3

I did add a diagram that should be helpful although as of right now we have not yet had a chance to made a video showing the Kat's Custom Engine Block Heater #KH11409 being installed on a 2015 Mazda CX-5. After checking out the instructions for…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Install Instructions for Kat's Block Heater KH11409

Product Page this Question was Asked From

Continue Researching