Replacement Latch for Bulldog 7k A-Frame Collar-Lok Trailer Coupler

Question

Question:

My latch has been smashed and I need to replace it. Do you have a part number for it?

asked by: K. S

0

Expert Reply:

To replace the latch on coupler # BD028386 you will need Bulldog High-Profile Latch Repair Kit, # BD024200. It comes with the high-profile latch handle, spring, latch wire, latch pin, push nut and cotter pin.

expert reply by: Michael H

0

Answer 1

Yes, the Drop Leg #LC405217 will fit your Lippert Electric Trailer Jack #LC285318 on your 2023 Grand Design Imagine XLS 22MLE travel trailer.

view full answer...

Answer 2

Yes, I went out to the warehouse and test fit legs on the Lippert Power Stance Electric Trailer Jack #LC69VR and found that the Drop Leg for Lippert Power Jack #LC405217 is a compatible match. This drop leg will slide into the inside of the inner…

view full answer...

Answer 3

If you're looking for the hard plastic piece that covers the manual override on your Lippert Smart Jack Electric Trailer Jack #LC643589, you can use part #LC733925. Aside from that and the drop leg #LC405217, Lippert does not offer any other…

view full answer...

Answer 4

Yes, the Drop Leg for Lippert Power Jack #LC405217 is compatible with your Lippert LC285318 electric jack.

view full answer...

Answer 5

Hey Marlin, from front to back the Bulldog Collar Lok part #BD028386 measures 17-5/8 inches. To get an idea how much longer this would be than what you have I would measure the overall length and the difference would be about how much closer to the…

view full answer...

Answer 6

We currently have 3 different trailer jack support plates. I have included other dimensions in the included photos except for #BDSPB50 which was not available. #DL22763 is 1/8 inch thick. #BD003135 is 1/8 inch thick. #BDSPB50 is 1/8 inch thick. The…

view full answer...

Answer 7

For locking a Bulldog Collar Lok coupler like the #BD028386 we have the part #e98888 which will work well to prevent the collar from sliding back.

view full answer...

Answer 8

Most square frame tubing will actually have a swelling in the steel that causes the frame to not be an exact rectangle. This is why you will see a bit of an angle on the Bulldog Collar-Lok Coupler #BD028386. I suggest using a large clamp to pull the…

view full answer...

Answer 9

I sure do! I recommend spraying all the moving parts and the areas around them on your Bulldog Collar-Lok Coupler item #BD028386 with WD-40. Use an excessive amount and completely saturate your coupler and let it sit. Make sure you spray it inside…

view full answer...

Answer 10

It sounds like you are used to using a Bulldog Collar-Lok Coupler, like part #BD028288, and that your new coupler is the Bulldog Collar-Lok Coupler w/ Pin, #BD028244, which is designed to be used as you have indicated. You have to grasp the coupler…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement Latch for Bulldog 7k A-Frame Collar-Lok Trailer Coupler

Featured Help Information

Miscellaneous Media

Continue Researching