Which Wiring Harness for RedArc Tow Pro Installation on 2006 Toyota 4Runner with Factory 7-Way

Question

Question:

What harness or other parts do I need to connect this to a 2006 Toyota 4runner Sport V6/4wd? Thank you

asked by: Justin

0

Expert Reply:

The correct harnesses to wire the RedArc Tow Pro Elite # RED44FR on your 2006 Toyota 4Runner is the Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Pigtail - Toyota # 3040-P along with # 331-TPH-017.

expert reply by: Erik B

0

Answer 1

If your 2006 Toyota 4Runner came with a factory 7-Way trailer connector as part of the tow package then you would need wiring harness #3040-P to install the P3 brake controller #90195. I have included a link to a video showing how a brake controller…

view full answer...

Answer 2

Since your 2005 Toyota 4Runner has the factory tow package with a 7-way trailer connector already in place at the back bumper you can use the two part numbers you referenced. Part #90885 is the Tekonsha Prodigy P2 proportional trailer brake…

view full answer...

Answer 3

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 4

The brake controller that I recommend for your 2018 Toyota 4Runner with the Tow Package is the Redarc Tow-Pro Elite #RED44FR because of how easy it is to use, the versatility in mounting locations, and the wide variety of towing applications it can…

view full answer...

Answer 5

If your 2005 Toyota Tacoma has the factory tow package then you can use the Custom Wiring Adapter #3040-P and Redarc Adapter #331-TPH-017 to install the Redarc Tow-Pro Liberty #RED52VR and avoid splicing into any wiring on your truck. If you have the…

view full answer...

Answer 6

The factory brake controller port on the 2005 Toyota 4Runner that came with a factory installed 7-Way trailer connector is located under the dash, to the left of the steering column. It is supposed to be taped to another wiring harness near the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Which Wiring Harness for RedArc Tow Pro Installation on 2006 Toyota 4Runner with Factory 7-Way

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching