What Size Valve Stem Does the Aluminum 15 Liger Trailer Wheel Use

Question

Question:

Do you know the size of the valve stem hole in these wheels? I am trying to check the compatibility with my TPMS system the OEM Ford trailer TPMS/camera kit.

asked by: Andrew

0

Expert Reply:

The Aluminum Liger Trailer Wheel part # LH35FR will have a 0.453" valve stem hole. Generally speaking, wheels under 16" will be 0.453" and wheels over 16" will be 0.625".

expert reply by: Conner L

0

Answer 1

Dan, we do have plenty of great options that will work with the Westlake ST235/75R15 Radial Off-Road Trailer Tire #WST54FR like the Aluminum Eagle Trailer Wheel #LH46VR which I personally like. Lionshead (the company that makes this wheel) makes a…

view full answer...

Answer 2

The pilot diameter on a wheel, like the one with part #AM30620, is the diameter of the bigger hole that is directly in the middle of the wheel. The pilot hole diameter of the wheel for the part I just measured is 2.84". I have attached a picture…

view full answer...

Answer 3

There isn't a guide to tell us what valve stem was installed on your wheels but you likely have rubber valve stems since the Westlake #WST54FR has a 65psi rating. Flow-through sensors a bit heavier and can end up waving back and forth on a rubber…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

What Size Valve Stem Does the Aluminum 15 Liger Trailer Wheel Use

Continue Researching