Installation of Reverse Lockout on Titan Dico Model 10 Coupler for Drum Brakes

Question

Question:

I am rebuilding an older actuator pre 2000 using a new master cylinder DX66FR and hopefully installing a reverse lockout T4748800. Is it correct to assume I no longer need the brass adapter/reducing orifice if the solenoid is installed? Most of my research indicates that I do remove it, but just want to verify. Does the solenoid regulate to the proper pressure 800 psi? for drum brakes? PS Your site and service are both fantastic!

asked by: J B

0

Expert Reply:

For your master cylinder # DX66FR, the Replacement Solenoid Valve for Titan Brake Actuators with Reverse Lockouts # T4748800 will serve you well. The solenoid does not regulate the pressure from the specific master cylinder when the valve is not activated so drum brakes will have up to 1000 psi and disc brakes up to 1600 psi.

expert reply by: Jason S

0

Answer 1

Hey Woody, The master cylinder you have is a Titan #23744, or a Titan 10/20 brake actuator, and we do have a replacement for you. The replacement is going to be part #DX66FR. This is made by Dexter, but is a direct replacement for your master…

view full answer...

Answer 2

Hey Adam! Demco is actually one of the higher quality options, and I would recommend it as a replacement for your Atwood 61101. Nothing is without negative reviews, and the majority for the Demco Hydraulic Brake Actuator #DM72VR are positive. Demco…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

Hello Gregg, I think I can help shed some light on what is going on. Basically, there are two ways to stop surge brakes from actuating when backing up the trailer. The first and most popular way to do this is to use a surge brake actuator with a…

view full answer...

Answer 5

The closest option we have to replace your Atwood 82543 actuator is part #DM72VR, which is the item you referenced. However, this actuator doesn't have the lockout like your Atwood does. For a lockout use #T4748800 as an electric lockout. It…

view full answer...

Answer 6

Hey Brian, the correct reverse lockout solenoid you need for your Dexter actuator would be the part #DX46UR. Did yours fail or are you wanting to add one?

view full answer...

Answer 7

Hey Sam, so in some states it is required that you have brakes on all axles of a triple axle trailer but in some states that is not true. It sounds like you already checked in your area but figured I would still mention it. I do need two key pieces…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Installation of Reverse Lockout on Titan Dico Model 10 Coupler for Drum Brakes

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching