Recommended LED Clearance and Cab Marker Light

Question

Question:

What bulb does this light have? Really looking for LED.

asked by: TOM S

0

Expert Reply:

The Truck Clearance and Cab Marker Light - Incandescent - Triangle - Amber Lens # CB22AB is a sealed light so there is not a replacement bulb option.

Since you want a LED option, I recommend the LED Trailer Clearance or Truck Cab Light - Submersible - 15 Diodes - Triangle - Amber Lens # CBL22AB.

If you want a kit, you can use the Pacer Performance Hi-Five LED Truck Cab Light Kit - Teardrop - 5 Piece - Amber LEDs - Amber Lens # PP20-206

expert reply by: Jason S

0

Answer 1

For a red-lens tear-shape clearance light you can use Optronics #CB22RB or the LED version #CBL22RB. Both lights are submersible. For amber lights you can use either incandescent type #CB22AB or LED-type #CBL22AB. Hardware is not included.

view full answer...

Answer 2

The Optronics LED Trailer Clearance or Truck Cab Light - Submersible - 15 Diodes - Triangle - Amber Lens item #CBL22AB does not come with the mounting hardware. I have attached a diagram showing the dimensions of the lights and the mounting holes. We…

view full answer...

Answer 3

Yes, the Optronics LED Trailer Clearance or Truck Cab Light part #CBL22AB does come with a thick foam mounting gasket which I have pointed out for you in the attached photo.

view full answer...

Answer 4

I think I have the perfect light for you. Take a look at the LED amber clearance light #MCL49AB. This light has 14 diodes so it will be bright and you can see it straight on and from an angle. I have included a link to a video review of this light…

view full answer...

Answer 5

Although we don't have any specifics for the lights on your 2009 Fleetwood Icon 24A I may have found a solution for you. We do have a selection of cab/clearance lights that are shaped at an angle like what it looks like on your Fleetwood. The…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Recommended LED Clearance and Cab Marker Light

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching