Replacement Extang BlackMax Tonneau Cover on my 1999 Ford F-150 with a 6.5 Bed

Question

Question:

I purchased a 1999 ford F150 with a 6.5 foot bed. I am fairly certain that it has a Extang Tonneau soft cover on it, no model number but the frame looks like photos I have seen on your site and the clamps are the same as your part number EX22000106.

asked by: Rich S

0

Expert Reply:

The Replacement Tarp for Extang BlackMax Soft Tonneau Cover part # EX1710 is the replacement you will need for the Extang BlackMax Soft Tonneau Cover part # EX2710

expert reply by: Randy B

0

Answer 1

To find the correct replacement tarp for your 2008 GMC Sierra you will need to know the brand and model of your current tonneau cover. The easiest way is to locate the serial number. Most of the time the serial number can be found on the driver's…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

Hey Don, thanks for the information! That's a significant amount of sag and a pretty heavy trailer, I recommend the Hellwig Pro Series Helper Springs item #HE79FR for the higher 2,500 lbs capacity. I doubt you're driving around with your bed…

view full answer...

Answer 8

Unfortunately you can not Doug. The factory hitch on your 2020 Ford F-150 Lariat is part of the rear step-bumper assembly. It's bolted to your frame and then the step-bumper bolts to the trailer hitch. Removing the factory hitch removes the…

view full answer...

Answer 9

Hey Wayne! The answer to your question is maybe. As you know, the Curt #C14017 is designed for the F-150 without the factory hitch. Typically this is because the factory hitch is integrated with the bumper and removing it to replace it with the…

view full answer...

Answer 10

Hi Bruce! The Access Toolbox Edition Soft, Roll-Up Tonneau Cover #A63FR will indeed fit your 2021 GMC Serra 1500 SLT with the short bed and your toolbox. This can be used with toolboxes that measure 19" to 21" long, so you are good to go!…

view full answer...

Answer 11

Hey Chris, No, there isn't an upgrade kit for your Generation 1 MORryde StepAbove RV Steps to make them a Generation 2. There is a Replacement Leg for MORryde StepAbove RV Steps - 2nd Generation #MR36DR, but because the Generation 1 steps'…

view full answer...

Answer 12

Hey Ken, welcome back! So this is a really great question but at the end of the day the Curt A25 part #C16046 and the B and W Companion part #BWRVK3600 that both fit the OEM pucks of your 2026 Ram 3500 are really nice hitches that you can't go…

view full answer...

Replacement Extang BlackMax Tonneau Cover on my 1999 Ford F-150 with a 6.5 Bed

Continue Researching