Installing Rubber Strip on Thule WingBar Evo Crossbars

Question

Question:

Tips installing rubber strip into Thule Wingbar Evo ?

asked by: Adam

1

Helpful Expert Reply:

The top rubber strips on the Thule WingBar Evo Crossbars like the 53" # TH711400 you were looking at are a bit different in design compared to the older AeroBar models. Out of the box you'll have a strip of rubber that likely needs to be cut (simply matching its length to the crossbar's).

Once you have the needed length, you will actually pull apart the strip down the middle, separating them into two narrower strips. Then it's simply a matter of pressing them down into the crossbar channel, one at a time. Start with the very end, pressing the strip until it secures into place. Once you have the end of the strip secured, laying the rest down along the crossbar is easier.

If you're having an issue with a specific part of this process just let me know and I will be happy to help you further.

expert reply by: Chris R

1

Brian M.

4/11/2024

The front rubber strip keeps blowing off at high speeds on both the front and back wingbars. I’ve replaced both twice. I’m following the directions on installation. What am I doing incorrectly?

Matt W.

6/4/2024

@BrianM - I am having the same issue and I’ve seen lots of comments on line suggesting the same. Frustratingly, it seems to be a design flaw! Will be tracking this post for any updates

Jameson C.

6/4/2024

@MattW I did find several people online with same problem. This is first I've heard of it but I am curious if yours did it immediately with the rack installed and then once it happened it kept happening or did you have a different situation play out.

Jamie

6/10/2024

@JamesonC same! I keep having to secure them down. One blew halfway off a couple weeks ago. Today it blew completely off! $50 to replace is not cool!

Answer 1

The Malone Universal Crossbar System #MPG201 is a more economical choice but it still does a good job. The design and quality of Thule's system is why they have such a large difference in price. Whether you go with the Thule Crossroads system…

view full answer...

Answer 2

Basically if you look at the rear of your 2019 Audi Q5 and you don't see a trailer connector then you don't have one from the factory. Worst case scenario you can call your local dealer with your VIN and they will be able to confirm either…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Installing Rubber Strip on Thule WingBar Evo Crossbars

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching