How to Trim Down Length of Fan-Tastic Roof Vent Garnish

Question

Question:

what do you recommend using to cut this to fit? the leg length on this is a little too long.

asked by: Tim S

0

Expert Reply:

Use masking tape to mark where you want to make your cut on the Garnish part # FVK2040-80 and then use a hand saw to cut along the masking tape.

expert reply by: Jameson C

0

Sam

1/27/2026

I had the same issue but tin snips work wonderfully well!

Answer 1

That is correct, the correct replacement roof flange for your MaxxFan Deluxe Roof Vent #MA00-05301K is the Replacement Roof Flange Assembly for MaxxAir Maxxfan Deluxe RV Roof Vent #MA49FR.

view full answer...

Answer 2

To install a roof vent lid like the Replacement Lid for MaxxAir MaxxFan Deluxe #MA05-30510 for the MaxxFan Deluxe Roof Vent w/ 12V Fan #MA00-05301K, isn't considered to be a difficult task at all. The unit does not have to be removed from the…

view full answer...

Answer 3

It sounds like you have the standard garnish for Fantastic Vents, but you will need one more measurement to make sure you get the correct one. This being the height of the leg. The Fantastic Vent Ceiling Garnish #FVK1060-80 will have a 6" leg…

view full answer...

Answer 4

When it comes to trimming The Ceiling Garnish for MaxxAir MaxxFan RV Roof Vent #MA54FR you will need to use masking tape to mark where you want to make your cut on the garnish. You will then need to use a hand saw to cut along the masking tape. I…

view full answer...

Answer 5

It sounds like you are looking for the Ceiling Garnish for MaxxAir MaxxFan RV Roof Vent - White #MA54FR. This will slide up into the ceiling opening for your MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote - Powered Lift - 10 Speed -…

view full answer...

Answer 6

The Off White Ceiling Garnish #FVK1060-80 will fit your application perfectly. It has the 6" leg that you'll need to cut down to fit your 5-1/4" application but aside from that everything else will match up perfectly. If you need a…

view full answer...

Answer 7

Hey James! The Garnish for Dometic FanTastic Roof Vent #FVK2040-80 is exactly what you're looking for! This is listed as fitting with a standard 14-1/4" x 14-1/4" roof vent, but the interior dimensions, depth, and lip depth all measure…

view full answer...

Answer 8

I can see why the diagram might be confusing for the Ceiling Garnish - Fan-Tastic Vents Roof Vent - 6" Leg #FVK1060-80. This garnish is listed as being a fit for 14-1/4" x 14-1/4" RV roof vent openings, but the actual dimensions will…

view full answer...

Answer 9

I would measure the 3/4 of an inch and mark it with masking taping all around it to use a reference point for where you will make the cut. For the actual cut I would recommend you use a fine tooth saw. Some people use soldering irons to make the cut…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

How to Trim Down Length of Fan-Tastic Roof Vent Garnish

Product Page this Question was Asked From

Continue Researching