Is There a Version of Equalizer part # 13-108-3 that Includes Mounting Hardware

Question

Question:

do you have the hardware/bolts for the install

asked by: Jeffrey S

0

Expert Reply:

We actually offer a version of the equalizer you referenced with all of the needed hardware with part # HAP-203-02. This would be the way to go since you are wanting the hardware as well.

expert reply by: Jameson C

0

Answer 1

It looks like you're likely trying to replace your hubs/drums on your Dexter axle and I do believe that the "0100" you found on the spec plate actually reads "D100" since that was one of the models that Dexter had for this…

view full answer...

Answer 2

I called Dexter and they told me that your Dexter P-12 SLR SN: D5287869 axle has a 3,000 lb weight capacity. If you need any parts please let me know what they are and I would be happy to offer my recommendation.

view full answer...

Answer 3

Although the Snap-on Reflector Ring, #A78RXB, will not fit the STL178 series lights like the Optronics GLOLight LED Stop/Turn/Tail Light #STL178RFPB, I do have a solution for you. Take a look at the Sealed, 6-1/2" Oval LED Trailer Stop, Turn and…

view full answer...

Answer 4

You would want to measure from the bottom of the ramp door all the way up to the spring above the door frame when it is open to determine the minimum length cable you would need for your spring. We do offer cables alone for enclosed trailer ramp…

view full answer...

Answer 5

The part numbers #BWGNRK1020 and #BWGNRK1020-5W are the exact same Turnoverball gooseneck hitch. We have two part numbers for it though as it shows up in two parts of vehicle fitguides as it works as a gooseneck hitch by itself or as the base rails…

view full answer...

Answer 6

The center bushing on the Dexter Equalizer for 3" Slipper Springs #13-108-3 can indeed be replaced if/when it's worn. You do not need to replace the entire equalizer. The correct replacement bushing for this particular unit is the part…

view full answer...

Answer 7

For your 2021 GMC Sierra 1500 with a 5-1/2 foot bed that is CarbonPro we have the BAK Revolver X4S part #BAK34ZR which is a hard roll up style cover. We also have the following: #TX79FR #BAK52FR #TX36FR #A25VR #A65FR #A75FR #A33ZJ #LOM76FR #A82VR…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Brian, we have a replacement inner member for the TDE LP8500 you have with the part #DX97UR. This replaces the inner portion of the actuator and allows you to leave the outer part attached so you don't have to do any welding.

view full answer...

Answer 10

Hey James, The part you mentioned is just the rack system and will fit the 2024 GMC Sierra 1500 with accompanying rails. This is the roof rack system in the pictures, and the right one will depend on the bed size of your '24 Sierra 1500: - 5-3/4…

view full answer...

Answer 11

Yes we do, the correct oil seal you would need is the part #10-56 which I verified has same dimensions as the 295924 that you have now.

view full answer...

Answer 12

Yes, the Dexter Suspension Bushing #K71-372-00 is the correct replacement center bushing for the 3" Equalizer #13-108-3. I verified this with my contact at Dexter.

view full answer...

Is There a Version of Equalizer part # 13-108-3 that Includes Mounting Hardware

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching