Size of Bolts Used for Buyers Products 5-Position Adjustable Lunette Ring with 3" Heavy-Duty Channel

Question

Question:

Please put the Bolt Diameter of tow ring and channel support bracket 2 in centers good all other dimensions OK but not Bolt Diameter. Some maybe 5/8inch some 3/4 inch Thank You

asked by: Gary C

0

Expert Reply:

The bolts that are used for the Buyers Products 5-Position Adjustable Lunette Ring with 3" Heavy-Duty Channel # 337B20145 have a 5/8" diameter and can actually be found with the replacement Bolt and Nut Kit # 337B9021.

expert reply by: Jon G

0

Answer 1

Hey David, the bolts that come with the Buyers Products Coupler Kit part #337B20145 that you referenced are 5 inches long. We actually sell replacements with the part #337B9021 if that's what you were looking for.

view full answer...

Answer 2

The overall length of the shaft of the bolt part #MBT58500-LN58 is 4-13/16 inches, the length of the threaded portion is 1 inch and the length of the smooth part of the shaft is 3-13/16 inch.

view full answer...

Answer 3

The etrailer Trailer Coupler #CTA-400 uses the Replacement Mounting Bolt with Nut for Adjustable Channel Couplers #MBT58500-LN58. This is a 5/8" grade 8 bolt. I have attached a diagram below which shows the full dimensions.

view full answer...

Answer 4

Unfortunately, we do not have what you need. We do have a variety of lunette rings that will fit the tongue of your trailer. You can go with something like the Titan Lunette Ring - Adjustable Channel Mount - 3" Diameter - Black Painted - 25,000…

view full answer...

Answer 5

The standard size lunette ring is 3 inches like the Demco Lunette Ring - Adjustable Channel Mount - 3" Diameter - Black - 25,000 lbs #DM09557-81. The 2-1/2 inch rings will not fit in the adjustable channel mounts where the vast majority of the 3…

view full answer...

Answer 6

You should NOT grease or lubricate a pintle loop like the part #C48550. Grease attracts dirt which will act like sandpaper and grind away at even the hardest of metals.

view full answer...

Answer 7

Due to the heavy duty nature of the lunette style pintle setups there isn't a bushing available for the rings. The sway you are experiencing is most likely due to improper trailer loading. If you move as much of the weight of your cargo forward…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Size of Bolts Used for Buyers Products 5-Position Adjustable Lunette Ring with 3" Heavy-Duty Channel

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching