Mounting Bracket and Wiring Harness for Peterson Clearance Light # M150R

Question

Question:

I found a bracket: Peterson trailer light bracket, 150-10 2 7/8 x 1 1/2. I also found trailer light red m150 R. It looks like these 2 parts are compatible. Is there a mounting kit that goes with this and do I need to purchase any wiring attachment. I have an exiting light in place on my boat trailer, that I need to replace. This size is the same as the existing light. I am not familiar with purchasing separate parts to create a usable light. I want to make sure I am ordering everything I need. Thanks for your help.

asked by: Jack V

0

Expert Reply:

The chrome base part # 150-10 is correct for the clearance light part # M150R and you will need a wiring harness for the light assembly as well like with part # 142-49 and you'd be set!

expert reply by: Jameson C

0

Answer 1

Looking at images for a 2017 Skeeter boat trailer it appears they use the Mini Clearance/Side Marker Light #TN96MR on the rear of the trailer to fit into a 3/4" hole. And the Thinline LED Clearance and Side Marker Light #AL91AB just in front of…

view full answer...

Answer 2

The Wesbar light that the replacement lens #102641 you were looking at fits has been discontinued. The company that bought Wesbar has been getting rid of a lot of their lights so it is unlikely you will find it. However, the Optronics Combination…

view full answer...

Answer 3

The older generations of the Wesbar submersible low-profile lights came with sealed light bulb capsules that are not replaceable like what you have in the picture you uploaded. Your best option is to replace the lights with new lights like part…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 11

Hey Rick. Unfortunately that's correct the Wesbar Tail Light 271594 has been discontinued. Our best option for replacing it is the LED Trailer Tail Light item #STL36RB for the passenger side and item #STL37RB for the driver side. The Wesbar light…

view full answer...

Mounting Bracket and Wiring Harness for Peterson Clearance Light # M150R

Products Featured in This Question

Continue Researching