What Fuse Rating is Needed to Protect the 12 Volt Accessory Power Cirucit on a 7-Way Connector?

Question

Question:

for the 12v power going to the trailer,i used 12 awg wire. what size fuse would be correct to use? thanks!

asked by: vernon d

0

Expert Reply:

To protect the 12 volt accessory power supply circuit, we recommend using a 40 amp inline circuit breaker, part number 9510.

expert reply by: Mike L

0

Answer 1

Since you have a 3,500 lbs axle, I recommend the 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles item #e22YR. These are for 4,000 lbs axles which will still work great with your Gulf Stream trailer. As far as your 26" measurement goes. If…

view full answer...

Answer 2

I do have an option for you but there are no trailer brake controller provisions on a 2022 Jeep Grand Cherokee L, therefore there are no plugs behind the dash to plug a brake controller into. In order to avoid a bunch of splicing into the vehicle I…

view full answer...

Answer 3

The brake controller install harness on your 2022 Jeep Grand Cherokee 4xe is under the dash, to the left of the steering column, taped to another harness near the emergency brake pedal. The Tekonsha brake controllers like the Prodigy P3 part #90195…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

What Fuse Rating is Needed to Protect the 12 Volt Accessory Power Cirucit on a 7-Way Connector?

Products Featured in This Question

Continue Researching