2 inch Outer Diameter Pipe Mount for Trailer Jack that is 2-1/4 inch Long

Question

Question:

What is the overall length of mount. Need something 2 1/4inch long. 2inch diameter.

asked by: Gary B

0

Expert Reply:

The overall length of the # DL22670 that you referenced is 1-7/8 inches long. For a similar pipe mount that is 2-1/4 inches long and 2 inches in outer diameter we have the part # BD015279 which would be what you'd need.

expert reply by: Jameson C

0

Answer 1

Attached is a link to our selection of Bulldog pipe mounts that you can filter through to find the correct one for your jacks. Unfortunately without knowing the model number of your jacks I wouldn't be able to give you an accurate answer. The…

view full answer...

Answer 2

It looks like the Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15 inch Lift - 5,000 lbs, item #BD178203 has a 2 inch outside diameter male receiver with a 5/8" pin hole that welds to the trailer frame, so you can use the Weld-On 2"…

view full answer...

Answer 3

I went out into our warehouse and pulled a Bulldog Round, Pipe-Mount Swivel Jack, part #BD178203, that has the same 2 inch inner diameter and 2.5 inch outer diameter pipe mount swivel jack as yours. I then test fit a Bulldog 2-1/2 inch Long, Weld-On…

view full answer...

Answer 4

The Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15 inch Lift - 7,000 lbs, item #BD198250, has a male pipe on the jack and a female receiver that welds to the trailer. This female receiver has an inside diameter of just over 2-1/2 inches to fit…

view full answer...

Answer 5

Hi Jeff! So the only combo with the 5 on 4-1/2 inch bolt pattern we have that provides that Load Range E rating is the Taskmaster Provider #TA56AR. It doesn't look like that tire is available by itself, either. This would certainly give you more…

view full answer...

Answer 6

I have two options for you to raise your trailer and gain more clearance between the fender and tire. The most cost effective option would be to flip the axles with a Dexter Trailer Springs Over-Under Kit part #K71-384-00 or part #K71-385-00. That…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

2 inch Outer Diameter Pipe Mount for Trailer Jack that is 2-1/4 inch Long

Product Page this Question was Asked From

Continue Researching