Is There a Replacement Handle for the HD50000101 Fulton Square Jack

Question

Question:

I NEED A NEW HANDLE FOR A FULTON HD50000101 FIXED MARINE JACK. WHAT HANDLE DO I NEED? I FOUND THE ONE FOR THE 2500LB JACK BUT NOT THE 5000LB. ARE THEY THE SAME? THANKS

asked by: Jamie S

0

Expert Reply:

I checked and unfortunately there is no replacement handle for the square tube Fulton Marine Jack # HD50000101.

I realize this is not the news you are looking for, but the only option if your handle is broken is to replace the jack with a new one.

expert reply by: Kyle S

0

Answer 1

For your application we have the 2K Bulldog Round, Snap-Ring Swivel Marine Jack #BD151464 which fits with the L-Bend Bracket #F500242 that has the 2-1/2" opening you mentioned (see attached photo) and secures using the Snap Ring #BD500241.

view full answer...

Answer 2

The Fulton Replacement Sidewind Handle Kit will fit certain Fulton jack models; TJ1055, TJ1057, TJ1222, TJ255, TJD125, TJ122F, XP15/L/W/WC and XP15L. If your jack is not one of these the handle will not work. I do not believe this handle will be…

view full answer...

Answer 3

The Fulton HD25000101 jack that you referenced can be found as part #FHD2500 on our site. For this jack the Replacement Sidewind Handle Kit is part #F0933305S00.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Is There a Replacement Handle for the HD50000101 Fulton Square Jack

Featured Help Information

Miscellaneous Media

Continue Researching