Is Yakima FrontLoader Wheel Mount Bike Carrier Compatible with Yakima Overhauler HD

Question

Question:

I plan on buying the Yakima Overhaul HD truck bed rack system and need to know if the Yakima FrontLoader Wheel Mount Bike Carrier - Roof Mount will clam around the Overhaul HD cross bars. If not do you have a something that I can attach to the Overhaul HD system to mount my mountain bikes?

asked by: Dale L

1

Helpful Expert Reply:

Yes, the Yakima FrontLoader bike rack # Y02103 does fit the bars of the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack # Y01151-58 that you mentioned.

expert reply by: Jameson C

1

Answer 1

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Daniel congrats on the new truck! The Lomax Stance Hard Tonneau Cover item #LOM54RV does indeed fit the 2026 Chevrolet Silverado EV with the Mid Gate. It also works with the Multi-Flex Tailgate that comes on the Trail Boss models. For a…

view full answer...

Answer 7

It sure is Doug and congrats on your new truck! The TruXedo Pro X15 Soft Tonneau Cover item #TX33TV has been confirmed to fit your new 2026 Ford Maverick. The TS Rails item #TH25FR are going to fit alongside the rails of the Pro X15 item #TX33TV on…

view full answer...

Answer 8

Hi Richard! From the top of the shank to the lowest part where the tri-ball sits on the #BWTS20067BMP is 11.125". If you have the balls at max drop with the tallest one hanging down that would be 12.5". We recommend at least 11" of…

view full answer...

Answer 9

If the Truxedo tonneau cover happened to have the Truxedo TS rail kit (we can't get it anymore) then use the Yakima Overhaul HD Ladder Rack part #Y01151-5755 would fit with it. If you do not have those rails though it would not work.

view full answer...

Answer 10

Hello Al, thanks for reaching out. Both of the tonneau covers you mentioned, the Pace Edwards UltraGroove #311-KMD7936 and the RetraxPRO XR #RTT-80233 are a fit for your 2026 Ram 3500 with the 8' bed. There are a few noteworthy differences…

view full answer...

Answer 11

Hi Thomas! The distance from the center of the hitch pin hole to the center of the ball on the #BW77BR is 13-5/8". This is designed to fit a 2-1/2" receiver with a 10k rating for the 2" and 21k rating for the 2-5/16" ball. What…

view full answer...

Is Yakima FrontLoader Wheel Mount Bike Carrier Compatible with Yakima Overhauler HD

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching