Front-Mount Trailer Hitch Receiver for 2019 Coachmen Leprechaun on Ford E-450 Chassis

Question

Question:

I have a 2019 Coachmen Leprechaun,with the f450 chassis. Will this C31078 hitch work on the front of my motorhome?

asked by: Richard M

0

Expert Reply:

We do have a front-mount trailer hitch receiver for your 2019 Coachmen Leprechaun, although according to my research, the Leprechauns that have a Ford chassis were built on a Ford E-450 chassis, as opposed to an F-450 chassis. So the front-mount hitch you need is:

- Draw-Tite Front Mount Trailer Hitch Receiver # 65053

I have added links to the instructions as well as a video showing this hitch being installed on a motorhome similar to yours.

expert reply by: Kyle S

0

Answer 1

I do have an option for you though there aren't custom fit hitches for box trucks. The frame is not really the issue but rather the body the up-fitter adds on which could hang down below the frame where the hitch mounts or actually use the holes…

view full answer...

Answer 2

Hey Sue, we have a front hitch that fits your 2022 Jayco Redhawk 24B with the Draw Tite part #65053 which would be exactly what you are looking for but the hitch you referenced only fits at the rear of vehicles. The #65053 definitely has the capacity…

view full answer...

Answer 3

We have the Draw Tite front hitch part #65053 that fits your 2022 Ford E-450 Jayco motorhome.

view full answer...

Answer 4

I went out to the warehouse and measured the Draw-Tite Front Mount Trailer Hitch Receiver part #65053 for you. The bolt holes are 38" apart left to right on center and 5" apart front to back on center. I have also attached a photo with…

view full answer...

Answer 5

Yes, the Draw-Tite #65049 that you referenced has been confirmed to fit the 2014 Ford F-450's including the cab and chassis models so it would work well for you. I attached an install video for you to check out as well.

view full answer...

Answer 6

The amount of cold cranking amps you need depends on how much you plan to lift/pull. The Badland Winch 2500 has an amp draw of 132amps at 2500 lbs, so any car battery should do. I would recommend including a charger in your setup. I recommend the…

view full answer...

Answer 7

I wouldn't recommend using a jumper box for long term use as you may over heat it but there are quite a few people who have used them with winches like the Dutton Lainson StrongArm #TW4015 and it worked well.

view full answer...

Answer 8

Provided that the battery can handle the 100 amp power draw at 12 volts then you can use it to power the Superwinch LT2000 #1120210. The wiring and fuses used for a 12 volt outlet such as a cigarette lighter are not rated high enough for the power…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Front-Mount Trailer Hitch Receiver for 2019 Coachmen Leprechaun on Ford E-450 Chassis

Featured Help Information

Miscellaneous Media

Continue Researching