6 inch Trailer Jack Wheel Replacement for Fulton Trailer Jack

Question

Question:

I need to replace a 6 wheel on a 77410 Cequent trailer jack. Capacity at least 1000 lbs . Need soon.

asked by: Kathleen P

0

Expert Reply:

We have the Replacement Wheel Kit for Fulton Marine Jacks - 6" # F6811S00 which is made by the same company as your Cequent jack. It's 6 inches in diameter, 2 inches wide, and has a center hole diameter with the bushing of 1/2 inch.

expert reply by: Jameson C

0

Answer 1

There are a few solutions for your tailgate to clear the jack on your trailer. I recommend to use a longer ball mount like #D-26, that would move the trailer back further away from the truck and give you clearance you need. If you know what size the…

view full answer...

Answer 2

Depending on how much you are looking to lower your trailer there are a few possible options. One option is to replace the ST205/75D15 tires currently on your trailer with the Westlake ST205/75R14 Radial Trailer Tire w/ 14" Silver Mod Wheel - 5…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

6 inch Trailer Jack Wheel Replacement for Fulton Trailer Jack

Featured Help Information

Miscellaneous Media

Continue Researching