Replacement Bearings and Seal for 2015 EZ-Loader Skeeter Boat

Question

Question:

Looking to replace sealed bearings on a 2015 ez- loader boat trailer..dual axle..for a skeeter boat VIN#******.Thanks

asked by: Daniel S

0

Expert Reply:

I was able to reach out to EZ Loader and found that the replacement bearings and seal you need are included in the Bearing Kit for #84 Spindle # BK2-100. This kit is for 1 hub assembly so you'll need 4 if you plan on replacing parts for each hub.

Attached is an installation video to assist.

expert reply by: Jon G

0

Answer 1

I have a few options for you to help with identifying the bearings on your trailer. The first and easiest method would be to crawl under the trailer and look for the axle tag on the beam. This should give an axle capacity which we can then use to…

view full answer...

Answer 2

What is the weight rating on your axle? I unfortunately don't have a way to see what bearings and seals your trailer uses but if you can let me know the weight rating and/or if you could measure the different dimensions of your spindle I can see…

view full answer...

Answer 3

I have a few options for you to help with identifying the correct hubs on your trailer. The first and easiest method would be to crawl under the trailer and look for the axle tag on the beam. This should give an axle capacity which we can then use to…

view full answer...

Answer 4

Looking at images for a 2017 Skeeter boat trailer it appears they use the Mini Clearance/Side Marker Light #TN96MR on the rear of the trailer to fit into a 3/4" hole. And the Thinline LED Clearance and Side Marker Light #AL91AB just in front of…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Bearings and Seal for 2015 EZ-Loader Skeeter Boat

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching