Mounting Hole Spacing for the Optronics LED Trailer License Plate Light

Question

Question:

Your info says 3-1/4 inch mount hole spacing and 3-1/2 inch spacing. Which is it. I need 3-1/2. Thanks,

asked by: Fred F

1

Helpful Expert Reply:

The two mounting holes on the Optronics LED Trailer License Plate Light part # LPL56CB which attach the bracket to the trailer are spaced apart 3-1/2" on center so it will be a direct fit for you.

expert reply by: Conner L

1

click to enlarge

Answer 1

Hey Mike! We don't have an all-in-one part that comes with the brackets and pigtail so you need to order those parts separately. The #AL91RB and #AL91AB will work with the Mounting Bracket #A91BB and then for a pigtail you can use the Right Angle…

view full answer...

Answer 2

Hey Andy, thanks for reaching out! The LED Trailer Light w/ Grommet #3375626157 comes as a kit and isn't available separately, but we do have some alternatives like the Optronics #STL12RB you picked up the other day. I also see that you got the…

view full answer...

Answer 3

The light dimensions of the Optronics LED #TLL12RK are 7-9/16" long x 2-3/4" tall x 1-3/4" deep and the hole size needed is 6.75" by 2.5 inches. I confirmed this with my contact at the manufacturer and I've attached a template…

view full answer...

Answer 4

The Taskmaster Radial Trailer Tire - Load Range G, item #TTWPRG235R16, is the closest tire to the 7.50-16LT tire that we have. Your tire has an overall height of 31.8 inches and a section width of 8.4 inches. The #TTWPRG235R16, tire has and overall…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Mounting Hole Spacing for the Optronics LED Trailer License Plate Light

Product Page this Question was Asked From

Continue Researching