Small Popup Trailer Leaf Spring Suspension Enhancement

Question

Question:

Good day I have small offroad trailer weighing around 1000 lbs unloaded was curious if you had an option like this Timbren system such as # TTRA1032 for a smaller weight type trailer

asked by: John

0

Expert Reply:

The Timbren # TTRA1032 is a great help to a trailer. For your small trailer you will want the Timbren Trailer Suspension Enhancement System Light-Duty Trailers 1,000 lbs # TTRA1702. It sounds like this is exactly what you are seeking.

expert reply by: Jason S

0

Answer 1

I would recommend to use the Timbren Trailer Suspension Enhancement System , part #TTRA1032, on your 3,000-lb utility trailer. This enhancement system is for medium-duty trailers. It has a weight capacity of 7,000 lbs. This does not mean that you…

view full answer...

Answer 2

The Timbren Trailer Suspension Enhancement System, part #TTRA1702 is designed for light duty trailers. This system has a weight capacity of 1,000 lbs. You do not want to exceed the trailers weight carrying capacity. Also, this system is for trailers…

view full answer...

Answer 3

Hi Rob, The Taskmaster Trailer Wheel Lug Nut part #TA66QR requires a 3/4" socket for installation. However, we do have the CE Smith Trailer Wheel Acorn Lug Nut part #CE16720 that is 1/2"-20 with a chrome plate finish and works with a…

view full answer...

Answer 4

Timbren makes a 7,000 lb capacity kit designed specifically for trailer axles like yours as part #TTRA1032 but we do not have a way for you to adapt your truck's Timbrens to your trailer.

view full answer...

Answer 5

To install Timbren helper springs #TTRA1032 the included bolt will need to be tack welded to the top plate, the top plate then gets welded to the bottom of the frame above the leaf spring stack. The 3 lower brackets will need to be welded together to…

view full answer...

Answer 6

The Timbren Trailer Suspension Enhancement System for Underslung Axles #T92MR is 5-1/4" tall. Timbren recommends The spring be in constant contact with the frame at all times. So ideally you will want exactly 5-1/4" from your axle tube to…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hello Matt, Thanks for writing in, that’s a great question. I’ve definitely heard the same concerns about the factory leaf springs on these, especially on larger toy haulers like your Wolf Pack. It makes sense to want something that’s going to hold…

view full answer...

Answer 9

Hey Bruce! The Timbren RV Trailer Suspension Enhancement System #T94KV is not designed to act as a lift kit or raise the frame. This will keep your trailer at the stock ride height and help improve stability and handling. Make sure you look over the…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Small Popup Trailer Leaf Spring Suspension Enhancement

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching