Dimension to Top of Handle for the Round Snap Ring Swivel Jack # TJB-2002-B
Updated 04/02/2019 | Published 03/29/2019
Question:
On the tjb-2002-b, what is distance to bracket to handle? Is it 3 inches?
asked by: Mike
Expert Reply:
From the center of the main mounting section of the Round Snap Ring Swivel Jack # TJB-2002-B to the top of the handle part that connects to the jack is about 5-1/2". The handle then dips down about 1-1/4" while the handle grip sits about 2-3/4" higher than that.
So if you are referencing where the handle connects to the jack then that is about 5-1/2" but if you are talking about the handle grip then that is about 7" (when you add the 5-1/2" and the 2-3/4" but subtract the 1-1/4").
Attached is a photo showing the measurements that I took.
Product Page this Question was Asked From
Round Snap Ring Swivel Trailer Jack w/ Footplate - Topwind - 15-1/4" Lift - 2,000 lbs - Weld
- Trailer Jack
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Topwind Jack
- 1001 - 2000 lbs
- Manual Jack
- 15 Inch Lift
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: swivel jacks trailer jack
- Shop: Replacement Retaining Ring for etrailer and Ram Snap Ring Swivel Jacks
- Shop: Round Snap Ring Swivel Trailer Jack w/ Footplate - Topwind - 15-1/4" Lift - 2,000 lbs - Weld
- Video: All About the Replacement Retaining Ring for etrailer and Ram Snap Ring Swivel Jacks
- Video: Curt Round, Snap-Ring Swivel Jack Review
- Video: The Low-Down on the Round Snap Ring Swivel Jack w/ Footplate
- Shop: Replacement Retaining Ring for Curt Snap Ring Swivel Jacks
- Shop: Curt Round, Snap-Ring Swivel Jack - Weld On - Topwind - 15" Lift - 2,000 lbs
- Video: Curt Round, Snap-Ring Swivel Jack: The Breakdown
- Shop: Round Pipe Mount Swivel Trailer Jack w/ Footplate - Sidewind - 14-7/8" Lift - 2,000 lbs - Weld
- Q&A: Can New Trailer Jack Be Installed On Trailer Using Same Mounting Hardware And Snap Ring
- Q&A: Mounting Holes Pattern of Round Snap Ring Swivel Jack
- Q&A: Thickness of Snap Ring for etrailer and Ram Jacks
- Q&A: Is There a Fulton XLT Jack Rated for 1,500LBS Which With Fit a 2-1/2" Diameter Snap Ring Bracket?
- Q&A: Pull Pin Diameter for Round, Pipe Mount Swivel Jack TJP-2002S-B
- Q&A: Does Bulldog Jack Mount # BD015279 Fit etrailer.com Swivel Jack # TJP-2002S-B
- Shop: Round Snap Ring Swivel Trailer Jack w/ Footplate - Sidewind - 14-1/2" Lift - 2,000 lbs - Weld
- Shop: Replacement Mounting Bracket for etrailer and Ram Snap Ring Swivel Jacks - Weld On
- Q&A: Replacement Jack for a Shelby Model 5730 Sidewind Jack
- Search Results: trailer tires and wheels
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Search Results: trailer hitch
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: How to Choose a Trailer Brake Controller
- Shop: Suspension Enhancement
- Search Results: trailer wiring
on Trailer Jack
