Replacement Hub For 2007 Marine Master Trailer With UFP 2,000 Lb Axle
Published 02/14/2020
Products Featured in This Question
Question:
I have a 2007 Marine Master trailer. To the best of my knowledge from reading the VIN plate, I have a 2,000# axle with a 5 on 4.5 hub with 13 wheels. The hub has a number stamped on the back of a 45263. I have searched and searched and cant seem to come up with anything as far as a hub assembly, or hub, bearings, and seals go. I have read that some of the 45263 parts are outdated? So, I was going to purchase an axle, but cant find a 2,000# axle with my dimensions, the only thing close is a 3,500# axle. The plate on the axle says to be a UFP A391426. The VIN on the trailer is . I would like to buy an assembly already packed and ready to installed. If not, I would like to get a new hub, bearings, and seal as my spindles look to be good. If that isnt possible Id like a new axle. I havent made an exact measurement but I believe hub face to hub face is ~74. I know this is all vague, but any help is appreciated. Thanks so much.
asked by: Brian Y
Helpful Expert Reply:
Your axle is a UFP axle which is made by Dexter Axle. I contacted them with your serial number and they were able to tell me your axle is a 2,000 lb axle with a 76" hub face to hub face and 62" spring center to spring center. The bearings are inner and outer part # L44649. Dexter said your original hub is a 2,500 lb idler hub.
You can replace your idler hub assembly with Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2 part # TA88545-2 that uses the inner/outer bearings part # L44649 with race L44610 and grease seal part # 10-60 which measures 1.50". The inner diameter of the L44649 is 1.063" and the inner diameter of the race is 1.980". There is not a 2,500 lb hub that is already packed.
I recommend to measure your spindle with digital calipers to be sure these measurements match up. I have added a diagram for your reference.
Product Page this Question was Asked From
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.06 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Continue Researching
- Search Results: l44849
- Search Results: l44610
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Q&A: Replacement Hub and Spindle for 2014 Ranger Trailer
- Shop: CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles - 5 on 4-1/2 - Pre-Greased
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 2.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: Replacement Race for L44643 and L44649 Bearings
- Shop: Replacement Trailer Hub Bearing - L68149
- Shop: Timken Replacement Trailer Wheel Bearing - L44643
- Shop: Grease Seal Kit- Triple Lip - Inner Diameter 1.719" - Outer Diameter: 2.565" - Qty 2
- Q&A: How To Determine Which Replacement Standard Hubs Will Fit Marine Master Trailer with Vault Hubs
- Video: Installing the etrailer Easy Grease Trailer Idler Hub Assembly
- Q&A: Does a Spindle with Scarring and Complete Bearing Failure Need to be Replaced
- Search Results: swan equalizer
- Search Results: torsion spring
- Search Results: coil spring
- Search Results: ramp spring
- Search Results: mobile home
- Q&A: Replacement 4 on 4.5 Bolt Pattern Trailer Rim and Radial Tire
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Measuring To Choose The Right Trailer Axle
- Shop: Trailer Wiring
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
on Trailer Bearings Races Seals Caps
