Location of Brake Controller Adapter Port to Install Prodigy P3 on 2019 Nissan Pathfinder

Question

Question:

2019 pathfinder electric brake controller wire connection under the dashboard location at ?

asked by: Louis B

0

Expert Reply:

To install the Prodigy P3 Trailer Brake Controller # 90195 in your 2019 Nissan Pathfinder you can find the brake controller port directly under the dash as in the accompanying photo.

This will allow you to plug in the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers # 3050-P.

I recommend going to the linked video showing this brake controller being installed on a Pathfinder; if you go to the 6:30 mark you can see the exact location.

expert reply by: Kyle S

0

click to enlarge

Answer 1

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 2

The Redarc Tow-Pro Elite Trailer Brake Controller part #RED44FR is a great option for a 2019 Nissan Pathfinder. If you already have the factory brake controller pigtail it would just simply hardwire into the included harness. You'd be attaching…

view full answer...

Answer 3

Weight distribution works to distribute the tongue weight of a trailer up to the front axle of the tow vehicle so that it will sit more level and handle/brake better. That being said the systems do not "reduce" tongue weight or allow you to…

view full answer...

Answer 4

After looking at the owner's manual for your 2022 Nissan Pathfinder, nothing says you cannot use sway control with the vehicle sway control system. There is a "Sway control device" section which only says make sure the device will work…

view full answer...

Answer 5

Ill, illumination, that is correct. You will not use that wire to install the Voyager brake controller #39510 on your 2016 Nissan Pathfinder. You will only need the black, red/green, brown/white, and blue. On the brake controller the white wire is…

view full answer...

Answer 6

Aluminum trailer frames or bodies can cause grounding issues so I suggest using a separate ground wire that runs from the rear of the trailer up to the main ground post in the junction box like #38656. You can join the ground wires for the individual…

view full answer...

Answer 7

The slight gap you see is normal. The drum is not supposed to make contact with the brake mounting plate. There are some instances when mixing brands of brakes, hubs, and axles, that won't line up properly but in this case it is normal. I did…

view full answer...

Answer 8

The correct way to wire your breakaway battery, like the Hopkins Engager #20400, is to have the black wire from the battery connected to the 12V power on your trailer, and then the blue wire to your breakaway switch which, in turn, connects to the…

view full answer...

Answer 9

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 10

While your spindle may have a diameter of 1-1/16 inch where the bearings ride the diameter where the threads are is actually 1 inch like what the part #5-23 that you referenced assuming you have a standard trailer spindle which it sounds like you…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Location of Brake Controller Adapter Port to Install Prodigy P3 on 2019 Nissan Pathfinder

Featured Help Information

Miscellaneous Media

Continue Researching