Replacement Wheel Cylinders For 1992 Bayliner Shorelandr Trailer

Question

Question:

I recently bought a 1992 Bayliner Rendevous deck boat which has a Shorelander trailer. I am looking for a replacement brake wheel cylinder. The VIN # on the trailer is very faded, I believe the # is ******?? If this is the correct number could you please give me the part number for the wheel cylinder? Thank you!

asked by: Darren G

0

Expert Reply:

I was not able to confirm with the VIN number what brakes are on your 1992 Bayliner Shorelandr trailer however they are most likely Dico brakes according to my research. If they are Dico 10 or 12" assemblies you would use Wheel Cylinder - 10" and 12" Single Servo RH part # BP17-020 and Wheel Cylinder - 10" and 12" Single Serve LH part # BP17-030.

expert reply by: Heather A

0

Answer 1

Unfortunately the Atwood 85736 cannot be replaced so you'd actually need an entirely new actuator. The closest replacement we have is the Demco Hydraulic Brake Actuator #DM72VR. This actuator has a gross towing weight capacity of 7,000-lbs, a…

view full answer...

Answer 2

Hey Brandon, Based on the information you've provided I recommend the DeeMaxx Disc Brake Kit #DE66YR. This disc brake kit has a corrosion-resistant "Maxx" coating finish on the hub/rotors, calipers, and brackets for a salt spray rating…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Wheel Cylinders For 1992 Bayliner Shorelandr Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching