Replacement Front Jack for Lippert Ground Control 3.0 Leveling Systems
Updated 06/18/2026 | Published 04/28/2026 >
Products Featured in This Question
Question:
I have a 2019 Montana high country 385br fifth wheel Im looking for a front jack replacement I have the 3.0 6 point leveling system is the lc362485 the correct part number
asked by: Wesley L
Expert Reply:
It sure is Wesley. The Replacement Front Jack item # LC362485 is exact what you will need for the 6 point Lippert Ground Control 3.0 Leveling System item # LC675817.
The Replacement Front Jack item # LC362485 can be used as a replacement for either the driver or passenger side front jacks.
What happened to your front jack that has you needing a replacement?
You can add this information, along with any other questions you have, where it says Add Comment.

Carol P.
5/2/2026
Our front jack stopped rising. Great product. Easy to replace. Highly recommend to purchase from etrailer. Quick delivery.

Allen
5/4/2026
Hello Wesley, I ordered just the jack as my motor was still good. With the camper connected to the truck, it was a quick and easy install. I did block up so I could set the pin down in the truck bed further back toward the tail gate to give me a bit more room. 15 minute job. Good luck!

Ken
6/17/2026
My Jacks really strain when loading and unloading as if they are not powerful enough. When I try to self level they can't finish and kick out a error code and I have to reset them every time.

Product Page this Question was Asked From
Replacement Front Jack for Lippert Ground Control 3.0 Leveling System
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Lippert
more information >
Continue Researching
- Shop: Replacement Front Jack for Lippert Ground Control 3.0 Leveling System
- Search Results: camper jacks
- Video: Replacement Front Jack for Lippert Ground Control 3.0 Leveling System Review
- Q&A: Will Replacement Front Jack for Lippert Ground Control 3.0 System Work On 2021 Open Range 5th Wheel?
- Search Results: lippert 30
- Q&A: Replacement Front Leg for a Lippert Ground Control 3.0 Leveling System
- Q&A: Replacement Front Jack for Lippert Ground Control 3.0 Leveling Systems
- Video: Review of the Replacement Front Jack for Lippert Ground Control 3.0 Leveling System
- Q&A: Correct Replacement Legs for Lippert Ground Control 3.0 Leveling System - 6 Point
- Search Results: 5th wheel front landing gear
- Search Results: rv water inlets accessories and parts
- Search Results: solera power awning parts
- Search Results: lippert leveling jack
- Q&A: Availability Of Replacement Rod And Nut For Lippert Ground Control 3.0 Jack Leg
- Q&A: Grease Maintenance Schedule For Lippert Ground Control 3.0
- Shop: RV Covers
- Shop: Classic Accessories PolyPro III Deluxe RV Cover for R-Pod Trailers up to 17' Long - Gray
- Q&A: Replacement Front Jack Tube for a Lippert Ground Control 3.0 System
- Shop: Replacement Hall Effect Motor for Lippert Components Ground Control 3.0 Leveling System
- Shop: Replacement Control Module for Lippert Ground Control 3.0 Leveling System - Prepped 5th Wheel RV
- Video: Lippert Ground Control 3.0 Electric Leveling System Replacement Control Module Review
- Video: Replacement Control Module for Lippert Ground Control 3.0 Leveling System: The Breakdown
- Search Results: lippert ground control
- Shop: Victron MultiPlus-II Inverter Charger with 2 AC Inputs - 2,400 Watts - 50 Amps - 24V - UL Listed
- Video: Benton LittleShift Bike Rack Fit Check - 2024 Chevrolet Equinox
- Shop: Replacement Plastic Check Valve for B&B Molders City Water Inlet - Black
- Shop: Replacement Gear Pack for Lippert RV Slide-outs w/ 2" x 2" Arm - No Roll Pin Assembly
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)



Wesley L.
4/30/2026
I'm thinking the screw part of it is messed up it's been throwing Alf jack error for a while and wouldn't self level. Talked to lippert on the phone trouble shooting it with a meter they told Meir was the control module . I replaced it and didn't fix the issue so I done some more research and seen where the screw part of the jack has a tendency to strip out so I'm going to try it and see if it fixes my issue