Weight
Published 01/29/2020
Products Featured in This Question
Question:
I’m considering a product like this but I have a few questions before I’m ready to make a purchase. First and foremost, I have an enclosed v-nose, will I be able to mount a product like this? Second, my trailer is rated for 7,000 but it looks like I’m running around 820 pounds for a tongue weight, should I bump up to a 10,000 pound set up? Lastly, with a standard ball mount, my trailer sits level with a 4” drop. It looks like I will need a longer shank to accommodate this with this head. Do you have a shank that’s compatible that I can achieve this amount of drop?
asked by: Brian Z
Expert Reply:
Thank you for all of the info on your trailer setup! Yes you can install a weight distribution system similar to the Curt TruTrack part # C17499 on a V-nose trailer like yours but the trick is to use a system that has chains on the spring bars so you can use a set of bolt on hangers like the part # C17005. The bolt on hangers can fit under the V-nose of the trailer unlike ones that require clearance above the frame.
So since you are running 820 lbs tongue weight you will want a system with a higher and wider range. The best way to pick out a system is to go with one that has a tongue weight range that the tongue weight of your trailer falls right into the middle of. Keep in mind that tongue weight also includes the weight of any cargo behind the rear axle of the tow vehicle.
For a system you'd most likely want the part # 17302 which has a tongue weight range of 800-1,000 lbs which would most likely be right what you'd need and would work great with the bolt on hangers.
For a shank to use with this system that has ability to do the 4 inches of drop you need you'd also want the part # C17123.
Product Page this Question was Asked From
Curt TruTrack Weight Distribution System w/ Sway Control - Trunnion - 8,000 lbs GTW, 800 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Trunnion Bar
- Fits 3 Inch Frame
- Fits 4 Inch Frame
- Fits 5 Inch Frame
- Fits 6 Inch Frame
- Includes Shank
- Top-Mount
- Fits 2 Inch Hitch
- Allows Backing Up
- 600 lbs
- 700 lbs
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Front Mount Hitch
- Shop: Vehicle Snow Plows
- Search Results: snow plow
- Q&A: Front Hitch that Fits 2020 GMC Sierra 1500 AT4
- Shop: SnowBear Snowplow for 2" Hitches - 88" Wide x 26" Tall
- Shop: SnowBear Elite Snowplow for 2" Hitches - 88" Wide x 26" Tall
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Detail K2 Elite Snowplow for 2" Hitches - 82" Wide x 19" Tall
- Search Results: backup camera
- Search Results: fastway wheel chocks
- Search Results: trailer wheel chocks
- Search Results: curt 17499
- Search Results: 17120
- Shop: Catalytic Converters
- Search Results: coupler locks
- Q&A: Measuring Fit of Fastway ONEstep Wheel Chocks
- Q&A: How to Measure to Determine if Fastway ONEstep Wheel Chocks will Fit a Dual-Axle Trailer
- Q&A: Correct Curt Weight Distribution System for 5K to 7K Trailer
- Q&A: Can a Weight Distribution System Be Installed on a Royal Crown V-Nose Trailer
- Q&A: Can Shank of Curt Weight Distribution C17499 be Replaced with One with More Drop
- Q&A: Can the Curt TruTrack or Equal-i-zer Systems Be Installed On a V-Nose Enclosed Trailer
- Shop: Equal-i-zer Weight Distribution Shank - 2-1/2" Hitch - 12" Drop
- Shop: Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 6,000 lbs GTW, 600 lbs TW
- Shop: Curt Trunnion Style Weight Distribution System with Shank - 10,000 lbs GTW, 1,000 lbs TW
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
on Weight Distribution Hitch
