Can a Weight Distribution System Be Installed on a Royal Crown V-Nose Trailer
Published 04/14/2016 >
Products Featured in This Question
Question:
looking at buy a V nose trailer and Im concerned if a torsion bar will fit, if its needed in the future. Dealer says its maybe 30 inches inside, 33 outside from the front portion of the A frame for attaching a torsion bar. 7 X 14 trailer, hauling two motorcycles. One is fully dressed @900 lbs and the other is about 750lbs. If necessary after purchase I want to make sure I can fit a torsion/load bearing distribution systems just in case. Driving 1000 miles one way. GMC Sierra 1500 4 x 4, 5.3L. Suggestions, recommendations. Local trailer parts and install dealers say it wont work? But the Royal dealer says it should. I guess I need to know length of torsion systems to see?
asked by: Chris B
Expert Reply:
It will be possible to use a weight distribution system with your V-nose trailer, but you will want to look at the specific system to ensure that there is enough room to mount the spring bar brackets on the frame.
The sway brackets that hold the spring bars of the weight distribution system will be installed close to the front of your V-nose trailer, based on the measurements from the dealer, but the distance will still allow a system like the Equal-I-zer to be installed on the trailer. For an Equal-I-zer system, the brackets need to be installed 27-32 inches back from the center of the coupler. I have attached a photo from the installation instructions showing this measurement for you.
Equal-I-zer offers different systems for trailers with different tongue weights. You will want to choose a weight distribution system based on the trailer's loaded and ready to tow tongue weight. The # EQ37060ET system has a maximum tongue weight of 600 pounds. The # EQ37100ET system has a max tongue weight of 1,000 pounds. And # EQ37120ET has a maximum tongue weight of 1,200 pounds.
The Pro Series # 49570 system that you referenced will not work well with your V-nose trailer. It is likely that the frame brackets would not be able to install far enough down on the frame.
I have attached a help article on weight distribution systems for you as well as a review video of an Equal-I-zer system.
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Front Mount Hitch
- Shop: Vehicle Snow Plows
- Search Results: vehicle snowplow snow plow
- Search Results: snow plow
- Shop: Plowser Hitch-Mounted Residential Snow Plow for Cars, SUVs, and Trucks - 90" Folding Blade
- Q&A: Front Hitch that Fits 2020 GMC Sierra 1500 AT4
- Shop: Detail K2 Elite Snowplow for 2" Hitches - 82" Wide x 19" Tall
- Shop: SnowBear Elite Snowplow for 2" Hitches - 88" Wide x 26" Tall
- Shop: SnowBear Snowplow for 2" Hitches - 88" Wide x 26" Tall
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Meyer HomePlow Residential Electric Snowplow - For 2" Hitches - 22" Tall
- Search Results: trailer wheel chocks
- Search Results: fastway wheel chocks
- Search Results: backup camera
- Search Results: 17120
- Search Results: curt 17499
- Shop: Catalytic Converters
- Q&A: Measuring Fit of Fastway ONEstep Wheel Chocks
- Q&A: How to Measure to Determine if Fastway ONEstep Wheel Chocks will Fit a Dual-Axle Trailer
- Q&A: Parts Needed for Equal-I-zer Weight Distribution to Tow 2016 Airstream with 4 inches of Drop
- Q&A: Can Shank of Curt Weight Distribution C17499 be Replaced with One with More Drop
- Q&A: Weight
- Q&A: Correct Curt Weight Distribution System for 5K to 7K Trailer
- Shop: Curt Weight Distribution Shank - 12" Long - 7-1/2" or 7" Drop - 1,500 lbs TW
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop

