Could TorkLift GlowStep Camper Scissor Steps Fit 2012 Open Range 337

Question

Question:

Will the TLA7504-8000 fit a 27.5 in opening ? I have an 2012 open range 337

asked by: Jim D

0

Expert Reply:

The mounting bracket width of the TorkLift GlowStep Camper Scissor Steps w/ Landing Gear # TLA7504-8000 that you referenced is 21-1/2 inches so it would easily fit in an opening that is 27-1/2 inches wide like you have on your 2012 Open Range 337!

expert reply by: Jameson C

0

click to enlarge

Answer 1

The only air bag kit currently available for a 2020 Ford F-350 FX4 is from Firestone, the Firestone Ride-Rite Red Label Air Helper Springs part #F95FV. This kit was actually just redesigned for the FX4 models. I know you were looking at AirLift but…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 4

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Hi Bill! Thanks for your pictures, they were extremely helpful! ^___^ The LCI Part #194170 on that tag you found means you have a 1621 pin box. The Gen-Y #GY45SR you were looking at is specifically for the Lippert 1116 and 1716 pin boxes, so you will…

view full answer...

Answer 12

Hey Bob, congrats on a setting up a new camper! Out of all of those options you'll also need to consider daily driving comfort unless that camper is a permanent addition to your truck bed. Listed below are a brief breakdown of each and a…

view full answer...

Could TorkLift GlowStep Camper Scissor Steps Fit 2012 Open Range 337

Product Page this Question was Asked From

Continue Researching