Can I Use Wiring Junction Box part # 3375601101 On A Boat Trailer

Question

Question:

Would this box be suitable for wet location, ie, boat trailer?

asked by: John

1

Helpful Expert Reply:

The Trailer Wiring Junction Box part # 3375601101 is not designed for a marine application unless you keep the junction box as far away from the the water as possible. If you mount the box on the tongue and it doesn't get backed into the water when launch the boat then you should be okay. There may be boxes out there made for marine applications but we do not carry them at this time.

expert reply by: Heather A

1

Answer 1

You could technically use a junction box like part #3375601101 for a 4-Way connection, like part #HM38134, but since junction boxes are designed for 7-Way connections you'll need to find a way to plug up the larger hole since you're only…

view full answer...

Answer 2

The Bright Way Trailer Brakeaway Kit #3802308 has a built in 1-AMP charger. So when your truck is connected it will be charging. There should be no draw going out while the trailer is disconnected so it should be ready to rip whenever you're…

view full answer...

Answer 3

I would be happy to help you put together the components you need to build your own trailer and do my best to keep the weight down. You are off to a good start with the Timbren Axle-Less Trailer Suspension System - Spindle w/Brake Flange item…

view full answer...

Answer 4

The Buyers Products Trailer Wiring Junction Box #3375601101 referenced in your question measures 6.5 inches long, 3.21 inches wide, and 2.5 inches tall when the cover is installed. The mounting holes at each end are spaced apart 7.38 inches on…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Can I Use Wiring Junction Box part # 3375601101 On A Boat Trailer

Product Page this Question was Asked From

Continue Researching