Replacement Red Trailer Clearance Light for 2007 Revolution RV Glo Brite 446A

Question

Question:

Can you help me find Red Marker light lens model TMG Glo Brite 446 A/R

asked by: Jerry S

1

Helpful Expert Reply:

We don't carry just a lens replacement for the Glo Brite 446 but we have the very similar Optronics LED light replacement part # MCL44RB1 for a red replacement that would work well! It's an LED and priced great too so it would be an easy solution.

expert reply by: Jameson C

1

Answer 1

The best option we have to replace the AV615BHM is the Furrion RV Stereo #DV1230BL. This is also a double din stereo with a DVD player and Bluetooth connectivity; just keep in mind it does require a cutout of 6-15/16" wide x 4" tall x…

view full answer...

Answer 2

We do offer teardrop style clearance lights in red, the Pacer Performance Hi-Five Truck Cab Light Kit part #PP20-215 which are sold as a set of five. These lights by law must be installed so that they face the rear of your vehicle. They come with the…

view full answer...

Answer 3

Although we don't offer a replacement lens or a clearance lamp assembly that fits those dimensions, we offer a 6 x 2 inch replacement LED clearance lamp, part #MCL76RB that would last up to 50 times longer than an incandescent lamp, would be much…

view full answer...

Answer 4

If the Glo-Brite 446A/R side marker lights on your Southwind RV are 4" long x 2" wide you can use #MCL31AB if you need LED lights or you would use #MC38AB for an incandescent replacement. If your Southwinds RV has a different sized or color…

view full answer...

Answer 5

Hey Scott, for your MaxxFan RV roof vent we have the smoke replacement lid part #MA10A40009K or the white part #MA10A40002K. The install is just as simple as you mentioned as well. Its basically just a couple screws.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Red Trailer Clearance Light for 2007 Revolution RV Glo Brite 446A

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching