Converting Air Command F3 Compressor System to Analog Gauge

Question

Question:

Can I install in cab analog gages to control my existing kit 2590? I’ve decided I would like analog control gages rather than using wireless remote. Is this doable?

asked by: Ron T

0

Expert Reply:

I spoke with Firestone just now and they told me that to convert the Firestone Air Command kit part # F2590 you have now to an analog setup would just require the Single Function Air Spring Control Panel # F2572 and you'd be set! This gives you a gauge you'd mount in your vehicle interior which has controls for the compressor built into it.

expert reply by: Jameson C

0

Answer 1

Yes, you can use the Single Function Air Spring Control Panel #F2572 to control your Air Command Compressor System w/ Light Duty Compressor #F2610 from your cab rather than using the wireless app. The ECU and wiring that came with your compressor…

view full answer...

Answer 2

I have attached a pneumatic diagram for you of the air compressor kit both with and without an air tank. You will want to look at these to ensure your air lines are attached in the proper locations. Once you have ensured you have the airlines ran…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 8

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 9

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 10

Hey Adam, we have just what you are looking for with the B and W fifth wheel rail kit part #BWRVK2402 which is a confirmed fit for your 2017 Ford F-250 and is the industry standard rail design which means it will fit the hitch you have. This is a…

view full answer...

Answer 11

The B&W Universal Base Rails and Installation Kit for 5th Wheel Trailer Hitches - 10 Bolt #BWRVR3200 will fit your 2018 Ford F-250 with aluminum bed but B&W doesn't recommend it. You will want to use some sort of spacers/isolators that…

view full answer...

Answer 12

Hey Robert, congrats on your new 5th wheel trailer! It is highly recommended to use a sliding hitch like the B&W Companion item #BWRVK3370 the shorter 6-3/4' bed on your 2026 Ford F-350. The slider will ensure you have clearance when making…

view full answer...

Converting Air Command F3 Compressor System to Analog Gauge

Products Featured in This Question

Continue Researching