Solution for Collar Lok Style Coupler with Broken Latch Mechanism

Question

Question:

Can this be repaired? Can I get just the peice that swings out and drive a new hinge pin in?

asked by: David P

0

Expert Reply:

Just the piece you broke on your Hammblow coupler is not replaceable. Only solution would be a new coupler like the Bulldog Collar Lok part # BD028463 that you referenced. Most likely your coupler is fatigued elsewhere too based on it breaking like yours did.

expert reply by: Jameson C

0

click to enlarge

Answer 1

It sounds like you might be needing the Replacement Coupler Cap Spring #BD500354 which fits the Bulldog Collar-Lok Couplers. If more than the spring is broken then we'll need to get you a completely new coupler. In this case let me know the what…

view full answer...

Answer 2

I don't think you are doing anything wrong necessarily. There are 2 possible issues that I can think of causing the problem. First, the spring may not be the correct size. A spring that is too short and/or not the correct diameter would fall out.…

view full answer...

Answer 3

As long as your tow vehicle can handle the additional amperage draw of supporting the additional trailer lights of your second trailer you can certainly add a 4-way to the back ofyour 2003 Forest River 5th Wheel Trailer. You would want to use a Draw…

view full answer...

Answer 4

When wiring up your 5th wheel trailer so that it can connect to the lights and brakes of your second UTV trailer it is just a matter of completing the circuits between the two. To add a 7-Way connector to the 5th wheel you can use the Bargman 7-Way…

view full answer...

Answer 5

Basically you will want to compress the spring part #BD500354 so that you can position it in place on your Bulldog Coupler. I attached a picture that shows where the spring installs at. It will just be a matter of compressing the spring to get it in…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Solution for Collar Lok Style Coupler with Broken Latch Mechanism

Featured Help Information

Miscellaneous Media

Continue Researching