What Size Snap Ring Does the Pull Pin, Easy Swivel Trailer Jack with Foot Use

Question

Question:

Whats the diameter of the snap ring? Im looking for one that has a 2.5 diameter

asked by: Alberto M

0

Expert Reply:

The Pull Pin, Easy Swivel Trailer Jack with Foot part # DL22683 is designed for a 2-1/2" diameter snap ring mount like what you said you had which is actually an industry standard so it would work well for you. Please note, this jack actually comes with a weld-on bracket and snap ring but since it sounds like you already have a bracket you can just discard this and use the jack and snap ring with your existing bracket.

expert reply by: Conner L

0

Answer 1

Hi George! Yes, the Dexstar Steel Mini Mod Trailer Wheel, Part #AM20242, can fit a 12 inch hub, but the hub size itself isn't what determines whether the wheel will fit. The important thing is that your hub has a 4 on 4 bolt pattern, since…

view full answer...

Answer 2

Hi Ken, The company that owned Bulldog went out of business early this year so we no longer have Bulldog brand items available on the site. The most similar jack I could find compared to the Bulldog 151110 is the Dutton-Lainson Pull Pin, Easy Swivel…

view full answer...

Answer 3

Hey Gary, it sounds like you might be able to use the Removable Steel Foot with Pin #DL22541 which has an outer diameter of 2" and an inner diameter of 1-3/4". Normally you would just remove a pin and remove the wheel to replace it with…

view full answer...

Answer 4

David, check out the SnapPad Donut #SN95FR. This is specifically designed for trailer wheel jacks with a 6"-8" wheel. I really like it over some of the others as it has a hole in the center so to not collect water. It can also be used on…

view full answer...

Answer 5

Yes! You can use Bearing Buddies on anything as long as you use the right size and as long as the axles are not EZ Lube axles with the grease fittings on the ends of the spindles. If your outer bearings are L44643, L44649, or L44640 then you can use…

view full answer...

Answer 6

A Dexter 3,500 lb axle will have a hub that uses 1/2" lug nuts, so the correct part is the CE Smith Trailer Wheel Lug Nut - Zinc-Plated Steel - 1/2" #CE11051.

view full answer...

Answer 7

For standard 3,500 lb axles the correct bearing kit is the part #BK2-100 which comes with L44649 and L68149 bearings. Bearing Buddy Protectors #BB1980A-SS are the ones most commonly seen on 3,500 lb hubs. This is designed to fit a hub bore of 1.980…

view full answer...

Answer 8

Based on your seal dimensions you have a 3,500 lb Lippert axle hub so for a Bearing Buddy you'd want the part #BB1980A-SS.

view full answer...

Answer 9

Yes you can reuse the spindle nut as long as its threads are not ruined and it has good form/fit/function. If you do need a new one or want a spare for future use you can get some here. Replacement Spindle Nut for Dexter Nev-R-Lube Hub and Drum…

view full answer...

Answer 10

We offer part #5-101 from TruRyde which is a tang-type washer intended for EZ-Lube spindles. This washer has a tab that fits between the notches on the castle nut to hold it in place. The inner diameter of this washer is 1-inch. The linked video will…

view full answer...

Answer 11

Yes, you can simply use the nut retainer part #6-191 on your spindle nut instead of the tang washer setup and it would work just fine. The EZ lube fitting would not be an issue at all.

view full answer...

Answer 12

If your trailer axle doesn't currently have brake mounting flanges you have a couple of options, one of which is to simply weld on flanges like you mentioned. A brake mounting flange needs to be welded perfectly square and concentric, which…

view full answer...

What Size Snap Ring Does the Pull Pin, Easy Swivel Trailer Jack with Foot Use

Product Page this Question was Asked From

Continue Researching