Bearing Buddy and Bearing Kit Recommendation for 3,500 lb Axles
Updated 06/24/2020 | Published 09/05/2017
Products Featured in This Question
Question:
I have a 1999 MacLander 18ft trailer and I need to find a bearing kit. Two axles 3500lbs. And bearing buddies. Please could you find a kit number for me?? Thanks, Wayne
asked by: Wayne
1
Helpful Expert Reply:
For standard 3,500 lb axles the correct bearing kit is the part # BK2-100 which comes with L44649 and L68149 bearings.
Bearing Buddy Protectors # BB1980A-SS are the ones most commonly seen on 3,500 lb hubs. This is designed to fit a hub bore of 1.980 inches.
expert reply by:
Jameson C
1
Product Page this Question was Asked From
Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649 and L68149
- Race L68111 and L44610
- 3500 lbs Axle
- etrailer
more information >
Continue Researching
- Search Results: 7~way molded trailer wire connector
- Search Results: 5 hole brake flange
- Search Results: bearing buddy
- Search Results: dexter ez lube
- Shop: Dexter Trailer Brake Drum for 9,000-lb to 10,000-lb Axles - 12-1/4" - 8 on 6-1/2 - Non-ABS
- Search Results: trailer hub assembly
- Shop: Bearing Buddy Bearing Protectors - Model 2441T-SS - Threaded - Stainless Steel (Pair)
- Search Results: 25580 bearing kit
- Search Results: 7 way blade
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 3.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: Kodiak Disc Brake Kit - 13" Rotor - 8 on 6-1/2 - Stainless Steel - 1/2" Bolts - 7,000 lbs
- Shop: DeeMaxx Disc Brake Kit w/ Actuator for Triple Axle Trailers - 13" Hub/Rotor - 8 on 6-1/2 - 7K
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Shop: Brake Controller
- Q&A: Bearing Buddy Recommendation for Dexter Hub 8-248 3,500 lb Axle
- Q&A: Selecting Correct Bearing Buddy for 8-Lug Hub on 7000-lb Axle on PJ Dump Trailer
- Q&A: Recommended Complete Disc Brake Conversion System For 10,000 lb Dexter Axles
- Video: Ultimate Overview of the Kodiak Hydraulic Brake Line Kit
- Video: The Low-Down on the Kodiak Disc Brake Kit
- Video: Feature Review Hydrastar Disc Brake Kit w/ Actuator for Tandem Axle Trailers
- Q&A: Replacement Hanger Kit, Leaf Springs, Brake Assemblies and Drums for Triple Axle 3,500 lb Axles
- Video: All You Need to Know About the Kodiak Disc Brakes
- Q&A: Where to Measure When Replacing a Trailer Hub
- Q&A: Triple-Axle Trailer Hanger Kit Recommendation for 7K Axles
- Q&A: Which Spindle Does Dexter Trailer Hub and Drum Assembly Fit
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Trailer Wiring
- Video: Let’s Check Out the Trailer Wiring Junction Box
- Video: Curt Discovery NEXT Trailer Brake Controller w/ Custom Harness: The Breakdown
Mark T.
6/24/2020
We have a 3500 lb dexter 5-lug drum brake axle. It is surge brakes. I am at a total loss for the axle model #. But I do know otbisba dexter and its the 5-lug and its rated at 3500# I can't get the caliper to give me a read on the id of the wheel hub (tire forces it out too far to get a reading). We lost 1 of the bearing buddies we had (must a been a bad bump) and the other is barried into a hub-o-meter. Would like, ideally, 1 bearing buddy & 1 brayden for it. But if we have to get a full pair of both I guess it is what it is.... Please advise as beat as u can. If I gota take apart the hub-o-meter mount to get u an od of the bearing buddy or id of the hub let me know please. And ty.