Weatherstripping For Front Header of Truxedo Sentry CT Tonneau Cover

Question

Question:

Im looking for the weatherstripping that sticks to the bulk head. I see you have some for a different model of cover. Do you have it for this one as well?

asked by: Joshua G

0

Expert Reply:

The part number for the weatherstripping you'll need is the # TX1706063 which is sold by the foot. For your cover you'd need to order a quantity of 5.5 feet.

expert reply by: Jameson C

0

Answer 1

Hi Lee; can you tell me which end cap it is based on the picture below? There are four possible options. Since you mentioned the foam I'm guessing it is either the Side Rail End Plug_RH Foam Seal or Side Rail End Plug_LH Foam Seal. The end caps…

view full answer...

Answer 2

Hi Tim, We do have the tapered rubber seals for the TruXedo Lo Pro tonneau cover, which is the Replacement TruXedo Tapered Weather Seal for Lo Pro Tonneau Covers #TX1114731. This is sold in increments of one foot, so if you need two feet of seal, for…

view full answer...

Answer 3

There is not a video out that shows you how to remove and replace the Replacement Header Seal for TruXedo Lo Pro Soft Roll-up Tonneau Cover #TX1704787 however it really is quite simple to do. All you're going to need to do is remove your current…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Weatherstripping For Front Header of Truxedo Sentry CT Tonneau Cover

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching