Replacing Panel on Extand Solid Fold 2.0 Hard Tonneau Cover

Question

Question:

how do you remove the rear hindge?

asked by: Tom

0

Expert Reply:

To remove the rear hinge on the Extang Solid Fold 2.0 you'll need to check the end of the hinge rails for a small plastic cap; that cap can be removed and will expose a # 20 Torx screw. Once you remove that torx screw you'll be able to remove any panels on that hinge and replace them as needed.

For a replacement panel on your Extang Solid Fold 2.0 you'll want to use the Replacement Tail Panel Assembly # EX83475-62 .

expert reply by: Erik B

0

Answer 1

The only tool you should need is just a screwdriver to remove the screw holding the endcap in place on the hinge between the the affected panels of your Extang Solid Fold 2.0 #EX83475. Once these are popped off you should be able to hold the loose…

view full answer...

Answer 2

To install/uninstall the panels on the Extang Solid Fold 2.0, you will need to remove the T20 Torx screws and hinge caps on one side. With the panel at a 45° angle, slide the panel towards the missing endcap. Then, rotate the hinge slightly and…

view full answer...

Answer 3

I found the picture you mentioned and while I wasn't able to find a better version that has easier to read text I can retype out the text of each step to make it easier to understand. Step 1. With the cover supported and laying flat, remove the…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 10

From what I can find the Norcold N306.3 fridge has a 2.7 cu ft capacity and is 20-1/8" wide and 26" tall. The most similar option we can offer is the 3.2 cu ft Everchill RV Mini Refrigerator #324-000111. The #324-000111 measures…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacing Panel on Extand Solid Fold 2.0 Hard Tonneau Cover

Featured Help Information

Miscellaneous Media

Continue Researching