Channel Width of Curt Pintle Hook with 2-5/16 Ball # C45910-15-20

Question

Question:

Is the channel inside dimension 3 inch on this mount? Thks.

asked by: MARK B

1

Helpful Expert Reply:

Yes, the channel width of the Curt Pintle Hook with 2-5/16" Ball # C45910-15-20 is 3 inches.

expert reply by: Jameson C

1

click to enlarge

Answer 1

I believe I have something that may work for you. The Convert-A-Ball Pintle Hook Combo, #PH1 comes with 3 stainless steel balls. They also offer an Adjustable Pintle Mounting Bar, #AMPC2. Purchasing this combination would give you the ability to…

view full answer...

Answer 2

I do have an option but the Flash Solid Steel HD Adjustable 2-Ball Mount part #FA49-00-5925 doesn't have an pintle hook/ball adapter. Instead, you can use the Curt Adjustable 2-Ball Channel Mount part #C45926 which has similar specs and can be…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Channel Width of Curt Pintle Hook with 2-5/16 Ball # C45910-15-20

Product Page this Question was Asked From

Continue Researching