Solution for Broken Torque Wrench When Installing Andersen Ranch Hitch AM3100

Question

Question:

I over torqued the top and side bolts. My torque wrench not Clicking at at any setting. I set it to 60 but I feel as though Ive went past it.

asked by: Ray

0

Expert Reply:

Best option would be to borrow or buy a known working torque wrench to verify that you are using the correct torque figures to install the Andersen Ranch Hitch # AM3100. Local auto parts stores typically will let people borrow them.

We do have the Powerbuilt Dual Drive Torque Wrench # ALL944001 which has a torque range of 10 to 150 ft lbs.

expert reply by: Jameson C

0

Answer 1

Hey Mitchell, The Timbren Suspension Enhancement System #TNRTTNB is designed specifically for Pro 4x models so it wouldn't be the right fit for your SV. Both the #TNRTTNB and #TNRTTN (which would be a fit for your SV) have 5" tall springs.…

view full answer...

Answer 2

I strongly recommend going with the SumoSprings Helper Springs item #SS95GR over Timbren's like item #TNRTTNB for your 4WD 2020 Nissan Titan. Both systems will support your rear end and keep your truck level while towing but you won't notice…

view full answer...

Answer 3

Thank you for providing a photo of your Pro Series weight distribution hitch #49570. The assembly/installation instructions for this kit are linked for you for reference and they indicate the correct torque specs for the included hardware. It is very…

view full answer...

Answer 4

I spoke with my Curt representative, who tells me that either Grade 8 or Grade 5 half-inch bolts are acceptable. In the past, they provided Grade 5 with their install kits, but recently changed to Grade 8. It doesn't matter which of the two bolts…

view full answer...

Answer 5

The bolts used to hold the weight distribution shank to the head is grade 8 on the Strait-Line Weight Distribution System #RP66082. I went out into our showroom and snapped a pic of what the bolt head to show you that it is a grade 8. Basically, to…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Ben! The Curt does have that restriction on the vertical bike racks so I recommend the TowSmart Trailer Hitch #TS82VR. This has a higher tongue weight capacity and will allow you to carry the VelociRAX. It would be a good idea to add the etrailer…

view full answer...

Solution for Broken Torque Wrench When Installing Andersen Ranch Hitch AM3100

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching