Are Mounting Holes of Replacement Electric RV Stabilizer Jack Motor # LC352338 Threaded

Question

Question:

Thanks for your reply Jameson but you did not give the tapped hole thread size. Can you give me that?

asked by: Edward E

1

Helpful Expert Reply:

Yes, I attached a picture of the motor part # LC352338 and you can see that the mounting holes are threaded.

expert reply by: Jameson C

1

click to enlarge

Edward B.

9/17/2019

Thanks for your reply Jameson but you did not give the tapped hole thread size. Can you give me that?

Jameson C.

9/17/2019

Sorry for not getting that to you sooner, the thread size is 10-32 according to my contact at Lippert.

Answer 1

The Replacement Control Switch for Lippert Components Hydraulic Landing Gear - White #LC138415 has 4 wires that connect to your landing gear motor. The blue, yellow, green and red colored wires do not have a diagram according to my tech contact at…

view full answer...

Answer 2

Hey Matt! The Hellwig Load Pro 35 Heavy Duty Helper Springs #HE93XR are only designed to give you additional support while towing/hauling. Aftermarket suspension enhancement cannot increase the capacity of your 2024 Silverado 2500. The only way to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Jonathan. If you're wanting to have an airbag set up alone with a 5th wheel hitch, you will want to get a FIrestone kit. The Airlift kit you asked about, part #AL88341, will not be able to be installed along side a 5th wheel, or gooseneck, as…

view full answer...

Answer 5

Hey Randy! I can definitely set you up with air bags and a compressor. I recommend Firestone since they make the most durable and reliable air bags. For a complete kit with an air compressor you can choose from the following: -Firestone Ride-Rite Air…

view full answer...

Answer 6

Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…

view full answer...

Answer 7

I'm sorry to hear about the motor ripping but we do have a replacement motor for your Lippert Stabilizer 337199. The correct replacement motor for that stabilizer is the Replacement Electric RV Stabilizer Jack Motor #LC352338.

view full answer...

Answer 8

The Lippert High-Speed Power Stabilizer Jack 337199 can be used on either the front or rear of a travel trailer as a stabilizer jack. Often times people think it is only for use on a 5th wheel as for the longest times most travel trailers sat lower…

view full answer...

Answer 9

That’s a great question Chadwick, and this is one of those situations where the change in technology really matters. The GE Appliances Low-Profile RV AC w/ Heat Pump part #GE26RR will replace your current ARC13AACBL2 setup, but it’s important to know…

view full answer...

Answer 10

The iRV34 is 9-5/16"W x 8-3/8"H x 1-3/4"D so you would be able to use the iRV RV Stereo #292-101079 but would need to install some trim on the top and bottom to fill in the gap left over from your old unit. Depending on the space…

view full answer...

Answer 11

Hello Sharman, thanks for reaching out. We don't have that exact SikaFlex 715 sealant in black, but we do have something very similar. Take a look at the following: - Alpha Systems 1021 Self-Leveling Sealant for RVs - Black - 10.3 oz - Qty 1…

view full answer...

Answer 12

Hey Tyler, so the difference is the amount of motors that each has. The Lippert PSX2 has two and the Lippert PSX1 like the part #LC298707 has a single motor. The foot print and mounting etc. is exact same so this will fit and work great in place of…

view full answer...

Are Mounting Holes of Replacement Electric RV Stabilizer Jack Motor # LC352338 Threaded

Product Page this Question was Asked From

Continue Researching