What Size Is the Bolt That Comes With the Anti-Rattle Hitch Lock for Kuat Transfer Bike Racks

Question

Question:

Is the actual pin a 1/2 inch or 5/8 inch?

asked by: Cheryl C

0

Expert Reply:

The Anti-Rattle Hitch Lock for Kuat Transfer Bike Racks part # HLT comes with a 1/2" diameter bolt/pin. It can be used in both 1-1/4" receiver tubes with a 1/2" hitch pin hole and because it threads into the shank on the bike rack can be used with 2" receiver tubes with a 5/8" hitch pin hole.

expert reply by: Conner L

0

Answer 1

The Curt Pin and Clip #F-4 that you referenced is designed to work on 1-1/4 inch hitches. The reason your hitch has a 1/2 inch hole and a 5/8 inch hole is because it is setup for an obsolete anti-rattle device Draw Tite J-Pin. We no longer carry the…

view full answer...

Answer 2

Hey Jim, You are right that both of those hitches, #C13382 and #C22MJ, fit a 2025 Crosstrek. Capacity wise these hitches are rated for the same 3,500lb capacity. The main difference comes down to the trim of the vehicle. The #C22MJ is not intended…

view full answer...

Answer 3

The biggest pro to using one valve stem to maintain air pressure in an air bag kit is that you always know that both bags will have an equal amount of pressure in them. If you have an application where equal pressure on both sides is always the norm…

view full answer...

Answer 4

You will need a threaded locking hitch pin to fit your specific bike rack. The etrailer Trailer Hitch Receiver Lock #e98882 will not fit with the threads that you have in the bike rack receiver tube. You will want to ensure that the hitch lock you…

view full answer...

Answer 5

Yep it sure is! The Kuat Hi-Lo Hitch Extender #HL20B you mentioned will absolutely allow you to mount your Swagman bike rack and lock it with the Locking Anti-Rattle, Threaded Hitch Pin for Swagman Hitch Racks #S64029. I've added some links below…

view full answer...

Answer 6

The best roof rack for your 2020 Jeep Gladiator consists of the Yakima 1A Raingutter Towers #Y00101 and Round 58" CrossBars for Yakima Roof Rack System #Y00409. As you can see from the accompanying photo, which is from Yakima, this roof rack…

view full answer...

Answer 7

Hey Patrick, the distance between the hitch pin holes on the Kuat Pivot hitch adapter part #PVP20B is 12-13/16 inches. That is how much distance it would add to the bike rack setup you have. You can see this and other dimensions in the attached…

view full answer...

Answer 8

Hey Mike, from the top of the shank of the Kuat Pivot to the very top of the pivoting assembly measures 4-3/16 inches. That's really close to what you mentioned so maybe measure again and see if the part #PVP20B would work or not. If not, let me…

view full answer...

Answer 9

At this time Kuat offers two pivoting hitch extenders for their racks. They have the part #PVP20B that you referenced which pivots out to the passenger side and the part #PVD20B which pivots out to the driver's side. The reason I recommend the…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

What Size Is the Bolt That Comes With the Anti-Rattle Hitch Lock for Kuat Transfer Bike Racks

Product Page this Question was Asked From

Continue Researching