Trailer Hitch that Fits 2007 Dodge Caravan with Stow N Go Seating

Question

Question:

Jameson C replied to my question at etrailer with the following: The Curt hitch # 13389 is the correct fitting hitch for your 2007 Dodge Caravan with stow n go seating. The other two hitches fit different vehicle variations. I have attached an image of the back of my van and you can see that the exhaust is on the passenger side, this differs from the image of the Curt hitch that is on your site. Is the image on your site wrong?

asked by: Jeff L

0

Expert Reply:

The Curt hitch # 13389 is the correct fitting hitch for your 2007 Dodge Caravan with stow n go seating. The other two hitches fit different vehicle variations.

I attached an install video for this hitch on a 2007 Town and Country similar to yours.

expert reply by: Jameson C

0

click to enlarge

Jeff L.

9/4/2019

Jameson C replied to my question at etrailer with the following: The Curt hitch # 13389 is the correct fitting hitch for your 2007 Dodge Caravan with stow n go seating. The other two hitches fit different vehicle variations. I have attached an image of the back of my van and you can see that the exhaust is on the passenger side, this differs from the image of the Curt hitch that is on your site. Is the image on your site wrong?

Jameson C.

9/4/2019

Thanks for getting back to me and including the picture you submitted. The picture you sent in actually matches a 2008 Dodge Grand Caravan which is a different model from a 2007. So based on that you'd instead need the Curt hitch part # 13364 and you'd be set. I attached an install video for this hitch for you to check out as well.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 12

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Trailer Hitch that Fits 2007 Dodge Caravan with Stow N Go Seating

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching