What Is the Correct Bearing Kit for a 2018 Winnebago Micro Minnie 2108DS

Question

Question:

I have a 2018 Winnebago Micro Minnie 2108DS. It has 3500 lb axles. I noted these Lippert numbers on the axle 126003 and 170613. Which bearing kit is correct for this trailer

asked by: Kelly S

0

Expert Reply:

The correct bearing kit for your 2018 Winnebago Micro Minnie 2108DS with Lippert 3,500 Lb axles is the Bearing Kit for #84 Spindles part # BK2-100 which uses L44649 and L68149 bearings.

expert reply by: Conner L

0

Answer 1

Hey Chris, since we know your 2023 Winnebago 2100BH has 3,500 lb axles the correct seal you would need would be the part #58846. Is your seal leaking?

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

I spoke with my contact at Lippert and he confirmed that the Lippert Components Power Tongue Jack 1817941 #LC285318 can be rotated to be best orientated for you. The jack can be un-bolted, rotated, and reinstalled.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

What Is the Correct Bearing Kit for a 2018 Winnebago Micro Minnie 2108DS

Product Page this Question was Asked From

Continue Researching