What Degree Lug Nut Should be Used with Kenda Karrier ST235/85R16 Radial Trailer Tire with Wheel

Question

Question:

Hi. Does this wheel require a 60° or 90° angle 1/2 - 20 wheel bolt? Thanks

asked by: Mark

0

Expert Reply:

The Kenda Karrier ST235/85R16 Radial Trailer Tire with 16" Black Mod Wheel # AM35010 uses lug nuts that have a 60 degree cone shape like the part # CE11051.

expert reply by: Jameson C

0

Answer 1

Yes you are correct. Since the wheel weight capacity of the Kenda Karrier ST235/80R16 Radial Trailer Tire with 16" Black Mod Wheel #AM34834 is lower than the tire you would be limited to the wheel capacity as the overall capacity of 3,050 lb…

view full answer...

Answer 2

Thanks for reaching out and the info on your 2006 Rage'N Falcon 3405 Toy Hauler! Since it has a GVWR of 14,000 lbs this means you likely have 6K axles and can use the 12" Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-458-459 (one kit…

view full answer...

Answer 3

It depends on how much clearance you currently have around your wheels. Ideally, you should have 3 inches minimum clearance between your fender and your wheels and an inch minimum between your sidewall and trailer frame/wall. As your wheel size…

view full answer...

Answer 4

If you are changing from a 15 inch to a 16 inch tire and wheel you will add more height to the trailer. With the size tire you currently have on your trailer the diameter is approximately 28.87 inches tall. To go with a tire like part #AM35010 which…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

What Degree Lug Nut Should be Used with Kenda Karrier ST235/85R16 Radial Trailer Tire with Wheel

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching