How Would Roller Bunks Install on Karavan Boat Trailer
Updated 03/03/2020 | Published 07/04/2019
Products Featured in This Question
Question:
I’m wanting to replace wooden bunkers with roller bunkers on my Karavan bot trailer. Y’all have answered a previous question with the suggestion to use two four foot roller bunks on each side. Please show or illustrate how do so on the pictured trailer.
asked by: Richard C
Expert Reply:
Since the picture you submitted belongs to Karavan I can't post it here on our site, but if you check out the attached picture you can see how a very similar trailer had a set of rollers like the part # CE27710 installed.
For a set of swivel brackets like what you see in the picture that are holding the bunks you'd then want the part # CE10003G-4.
I also attached a couple install video links for you to check out as well.
Product Page this Question was Asked From
CE Smith Roller Bunks for Boat Trailers - 6 Rollers Each - 5' Long - 1,500 lbs - 1 Pair
- Boat Trailer Parts
- Bunks
- Rollers
- Roller Bunk
- Rubber
- CE Smith
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: boat trailer parts
- Shop: CE Smith Roller Bunks for Boat Trailers - 6 Rollers Each - 5' Long - 1,500 lbs - 1 Pair
- Shop: CE Smith Bolster and Swivel Bracket Assemblies for Roller Bunks - Galvanized Steel - Qty 4
- Video: Breaking Down the CE Smith Bolster and Swivel Bracket Assemblies for Roller Bunks
- Search Results: boat trailer bunk brackets
- Shop: CE Smith Keel Roller Assembly for 3" Wide Trailer Tongues - Galvanized Steel and Black Rubber
- Shop: Tie Down Marine Slides for Boat Trailer Bunks - Fits Two 8' Long 2x4 Bunks - Black
- Search Results: winch
- Search Results: trailer roller
- Search Results: bow roller
- Search Results: boat winches
- Search Results: boat trailer winch trailer winch
- Shop: CE Smith Bow Roller Bracket for Winch Stands - Pre-Galvanized Steel - 13-3/16" Tall - Bolt On
- Shop: CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 13" - Qty 4
- Video: CE Smith Bolster and Swivel Bracket Assemblies for Roller Bunks: The Breakdown
- Shop: CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 11" - Qty 4
- Video: Review of Tie Down Boat Trailer Parts - Wobble Roller Bunk Assembly Boat Trailer - TD79FR
- Video: CE Smith Boat Trailer Roller Bunks Water Test
- Video: What to Know About the CE Smith Deep V Keel Roller Assembly for Boat Trailers
- Video: CE Smith Deep V Keel Roller Assembly for Boat Trailers Review
- Video: Dutton-Lainson Boat Trailer Roller Bunk Bracket Installation
- Q&A: Will the CE Smith Bolster and Swivel Bracket Assemblies CE10000G-4 Work on a Tritoon Trailer?
- Q&A: Will CE Smith bolster Brackets for Pontoon Boat Trailers Fit Any Trailer
- Q&A: Adding Bunks to 20 Foot Boat Trailer with Deep V Hull
- Q&A: How To Determine Correct Bunk Boards and Mounting Hardware For 17' V Bottom Boat
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Boat Trailer Parts
Chris
3/2/2020
Do you know of anyone who has installed these on a CE Smith Model 48810 Multi-Sport trailer? In particular where this model trailer is used to transport a Twin Troller X10 boat? The TT X10 has three ribs running down the tunnel between the pontoons so my concern with these rollers is that only the middle rollers would be supporting the boat on the two outer ribs. Can the middle rollers be removed so that the two outside rollers could carry the weight of the both on either side of each rib? I’m not sure is this would cause problems with the hull if the bunks or rollers are not supporting the boat on the outer two ribs?