CE Smith Bolster and Swivel Bracket Assemblies for Roller Bunks - Galvanized Steel - Qty 4

Ask the Experts about this CE Smith Boat Trailer Parts

• Brackets To Install Bunks on 2010 Karavan # KBE-1250-46 Boat Trailer
  We do not have a way of determining which bunk brackets your Karavan trailer might use, but I may have a solution. If you have one already you could take photos and throughly measure it so we can look at our inventory of parts. In the mean time I have posted a link that shows many of our bunk brackets. I hope this is helpful.
  view full answer...
• What Size Mounting Hole is On Top of Roller Bunk Bracket CE10003G-4
  The hole in the top of the swivel bracket of the bunk bracket part # CE10003G-4 is 7/16 inch in diameter. You would need to go with a nut and bolt that matches that hole size the best when securing your roller bunk to it. We don't have a specific size recommendation as applications can differ.
  view full answer...
• Installation Of Roller Bunks On Karavan Boat Trailer
  If the brackets don't allow enough swivel to allow the roller bunks to fit flush on the boat, I recommend replacing the brackets with bolster brackets that will allow enough swivel like the CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 9" - Qty 4 # CE10000G-4. This bracket can be installed with CE Smith U-Bolts - Galvanized - 3-13/16" Long x 3-1/16" Wide x 1/2" Diameter - Qty 4 # CE15283GA-4. You will want the proper fit for best load support and function.
  view full answer...
• Is There a Way to get a 14 Inch Bolster Bracket?
  We do have an option to get you to the 14 inches, but it will be parts that need to be purchased separately. So with that being said, the CE Smith Bolster Bracket # CE10102G will measure 12 inches tall and if paired with the CE Smith Swivel Bracket # CE10200G, it will get you to the 14 inches.
  view full answer...
• Recommended Roller Bunks Replacement for Wooden Bunks for G3 1860 Boat
  We do have a variety of roller bunks that can be used as a direct replacement for carpeted bunks. I recommend either going with the 2,500 lb capacity which comes in Black # DL21754 or Silver # DL21740, OR the 3,000 lb capacity which also comes in Black # DL21755 or Silver # DL21741. I have also attached a link to all of the options that you can check out, as well as a link to all of our brackets if they also need replacing.
  view full answer...
• Can I Use Roller Bunks and Carpeted Bunk Boards Together on Boat Trailer
  I'll start off by saying that I've seen quite a few boat trailers that use a combination of rollers like the CE Smith Roller Bunks for Boat Trailers - 6 Rollers Each - 5' Long - 1,500 lbs - 1 Pair # CE27710 and a carpeted bunk like the CE Smith Carpeted Bunk Boards for Boat Trailers - 7' Long - 1 Pair # CE27845. The rollers definitely help if you're on a lot of shallow or steep boat ramps and combining the two gives you the best of both worlds, with the rollers on the bottom and boards...
  view full answer...
• Recommended Roller Bunks For 26' Seaswirl Boat Weighing 4200lbs
  You could absolutely replace your standard wooden bunk boards with the CE Smith Roller Bunks for Boat Trailers - 5 Rollers Each - 4' Long - 1,500 lbs - 1 Pair # CE27700 you were looking at, but since they have a 1500lb rating each you will need to make sure to use at least 3 pairs due to your boat being 4200lbs. These roller bunks will allow you to load your 26' Seaswirl much easier. The easiest way to install these is to just attach them directly to your existing bunk boards, but...
  view full answer...
• Recommended Upgrades to CE Smith Boat Trailer Model 48810
  Upgrading the carpeted bunks on your CE Smith Boat Trailer to roller bunks like the CE Smith # CE27710 is a great way to upgrade the trailer. These will allow for much easier loading and launching of your boat and reduce the stress put on your hand winch during operation. These are 5 foot long bunks that will work perfectly to replace the 5 foot bunk boards on the trailer. You can use the Bunk Brackets # CE10003G-4 to mount them to the trailer. It looks like the trailer is equipped with...
  view full answer...
• Comparing Dutton-Lainson and CE Smith Roller Bunks
  There isn't a whole lot of difference between Dutton-Lainson roller bunks # DL21741 and CE Smith roller bunks # CE27710. Both have 5 foot long sections. Each section is rated for 1500 pounds. There are 6 rollers per section on both. Both are made with galvanized steel and heavy duty black rubber rollers. The main difference besides price is the shape of the rollers is not exactly the same. Either set can be mounted on a bunk or independently. To mount independently you would need...
  view full answer...
• How To Choose the Correct Roller or Carpeted Bunk Boards for a Trailer
  The size of bunk board or bunk roller you will need for your boat trailer is based off the hull size. However, generally speaking the manufacturer knows what size roller/bunk works best for the boat/trailer. Therefore I recommend using the same size that the trailer came with but it wouldn't hurt to go a bit longer if you have room. If you are switching from rollers to carpeted bunk boards then I would go longer. For the carpeted bunk board option we have part # CE27800 which are 36"...
  view full answer...
• Recommended Roller Bunks For LoadRite PWC Trailer
  The CE Smith Roller Bunks for Boat Trailers - 6 Rollers Each - 5' Long - 1,500 lbs - 1 Pair # CE27710 will work well for your LoadRite trailer. If you want the 4 foot option, you can use # CE27700. This will work with the CE Smith Bolster and Swivel Bracket Assemblies for Roller Bunks - Galvanized Steel - Qty 4 # CE10003G-4. These brackets will follow the contours of your boat. For installing the brackets, I recommend the CE Smith U-Bolts - Galvanized - 3-13/16" Long x 3-1/16" Wide x...
  view full answer...
• How Would Roller Bunks Install on Karavan Boat Trailer
  Since the picture you submitted belongs to Karavan I can't post it here on our site, but if you check out the attached picture you can see how a very similar trailer had a set of rollers like the part # CE27710 installed. For a set of swivel brackets like what you see in the picture that are holding the bunks you'd then want the part # CE10003G-4. I also attached a couple install video links for you to check out as well.
  view full answer...
• Roller Bunk Recommendation for a Boat Trailer with Wood Bunks
  The CE Smith Roller Bunks, # CE27700, that you referenced would be a great option for your boat trailer. These roller bunks are 4 ft long and they can be mounted directly on top of your current wood bunks. You can also use the CE Smith Mounting Brackets, # CE10003G-4, if you want to replace the wood bunks with the roller bunks. Keep in mind, these bunks have a weight capacity of 1,500 lbs, but based on your photo, I do not think you will have much of an issue with that.
  view full answer...
• Can Roller Bunks Be Used on Tritoon Boat Trailer
  Roller bunks like those shown on the linked page will work just as well on a 3-hull tritoon as on a pontoon boat. If you intend to mount the rollers onto the flat surface of existing wooden/carpeted 2x4 bunk boards you will want to use a flat-bottom type roller like # DL21741, but we also have rollers like # DL21755 that have a channel that fits over the narrow side of a 2x4. The flat-bottom type can also be directly mounted to bolster brackets like # CE10003G-4 as shown in the linked...
  view full answer...
• Using Roller Bunks for PWC Ramp & Trailer
  Roller bunks like the 5-foot Dutton-Lainson # DL21755 and the other similar products shown on the linked page will work best when they are positioned on the trailer or ramp surface in such a way that allows the maximum contact between the watercraft's hull and the flat top surface of the rollers. The fuller and more even the contact the easier the rolling action will be. On a PWC the hull can have many different profiles or shapes. These can include the common V and modified V, and the...
  view full answer...
• Does Rhino Rack Roof Rack part # RR44SR Come with Fit Kit and Install Hardware
  The Rhino Rack roof rack part # CE10003G-4 that you referenced comes with all needed install hardware and fit kits to install on a vehicle.
  view full answer...
• Can I Remove the Keel Rollers and Add Bunk Rollers to a Boat Trailer for a Smoker Craft Boat
  I would be apprehensive about completely removing the keel rollers, especially if they support any weight. Removing the keel rollers would force the bunks to support more weight. This could be dangerous with the bouncing affect trailers and boats experience when towing. To make sure it is completely safe to remove the keel rollers without potentially damaging the boat, I recommend contacting Smoker Craft directly because they would be the best source to tell you if the hull of your boat...
  view full answer...
• Roller Bunk Recommendation for Jet Ski Ramp
  For the 10 foot long bunks you have two sets of the CE Smith roller bunks part # CE27700 would work well for you. These can be mounted directly to the wooden bunks you have already or you can remove them and install them with the brackets part # CE10003G-4. The steel of these buns are galvanized which will do an excellent job preventing rust and corrosion. They would last longer than wood being constantly submerged.
  view full answer...
• Roller Bunks For Shorelander Boat Trailer And Lund Fury 1600 Aluminum Boat
  You have a couple of options for rollers on your Shorelander trailer. If you want to completely cover the 7 foot bunks you currently have, you can attach a 4 ft roller like part # CE27700, and cut another to cover the 7 ft board. If you do mount the roller bunks to the boards you currently have you will want to make sure your rollers for the bow are adjusted at the proper height to offer support for the boat when loaded. I have attached a link to our boat trailer parts. Another option...
  view full answer...
• Recommended Bunk Rollers And Hardware For 18.5 Foot Bass Boat
  No, one 5 foot long section is not enough for the support of your boat unless you will be using a combination of rollers and bunk boards. The CE Smith Roller Bunks for Boat Trailers - 6 Rollers Each - 5' Long - 1,500 lbs - 1 Pair # CE27710 will work well for your 18.5 foot bass boat if you use 2 roller sections on each side. You can see a similar install in the video review I've attached. You can use two 4 foot long sections on each side and still support your boat well. For that...
  view full answer...
• Recommendation on Replacement Boat Trailer Bunks with Roller-Bunks
  Yes, can replace your current wooden bunks with a set of roller-bunks, like the CE Smith Roller Bunks # CE27710. Upgrading to roller-bunks will improve the loading and unloading of your boat. The roller are made of a heavy-duty rubber that will not only absorb the shock when loading and unloading your boat, but the rubber roller will protect the hull of your boat from scratches. CE Smith roller-bunks measure 5 feet long and will have 6 rollers installed on each bunk. The bunks have...
  view full answer...
• Does it Matter Which Side of the Crossmember the Boat Bunk Brackets Install On
  It doesn't really matter which side of the crossmember of the trailer frame the bunk brackets install on. As long as they are torqued down properly either way will be perfectly safe. Since the brackets have swivels like # CE10003G-4 there would be no need to cut the boards at a different angle.
  view full answer...
• Recommended Roller Bunks For Commercial Crab Boat 5,000-6,000 lbs
  For your Commercial Crab Boat, I recommend the CE Smith Roller Bunks for Boat Trailers - 5 Rollers Each - 4' Long - 1,500 lbs - 1 Pair # CE27700. These 4 foot long rollers are 4-3/4 inches wide x 2-1/2 inches diameter. I recommend using the CE Smith Bolster and Swivel Bracket Assemblies for Roller Bunks - Galvanized Steel - Qty 4 # CE10003G-4 to support it. I would use extras for more support and better weight dispersion on your frame due to the size and weight of your boat. As long...
  view full answer...
• Recommended Roller Bunks for Livingston 14 with Catamaran Hull
  Sounds like your trailer has fixed carpet-covered 2x4s that support the hulls and you want to replace them with roller bunks. The CE Smith Roller Bunks, # CE27700, that you referenced, would be a great option for your catamaran boat trailer. These roller bunks are 4 ft long and they can be mounted directly on top of your current wood bunks. You can also use the CE Smith Mounting Brackets, # CE10003G-4, if you want to replace the wood bunks with the roller bunks. For 5 ft roller bunks use...
  view full answer...
• When Using Two Sets Of CE Smith Roller Bunks For Boat Trailers Is Weight Capacity Increased
  I called my contact at CE Smith about the Roller Bunks for Boat Trailers, part # CE27700. They said since you are planning on using 4 bunks instead of 2, the rollers would have no problem with the additional 500 lbs as you described, as long as the weight is distributed evenly on the roller bunks. These roller bunks can be attached to wooden bunks or you may want to use swivel brackets like part # CE10003G-4. If you need U-bolts I recommend part # CE15283GA-4 for 4 U-bolts....
  view full answer...
• Recommendation for Spool Rollers for 18ft Wood Boat on Custom Boat Trailer
  I do have a solution for you, however the CE Smith Spool Roller Assembly # CE32100G aren't wide enough to safely support the boat keel of your 18 foot Norwegian Faering. I recommend something a bit wider like the CE Smith Deep V Keel Roller Assembly # CE10453G with an 8 inch roller and mounting slots spaced 6 inches apart. You will want to have one for each cross member on your boat trailer. The only other thing you will need are 1/2" or 7/16" fasteners. I have included a video review...
  view full answer...
• Recommended Bunk Board Brackets
  We definitely have options for brackets to mount your bunk boards. This will depend on the size needed, of course, but here are a couple options for you to take a look at. The CE Smith # CE10003G-4 will come as a 4 pack and are 11 inches tall, including the swivel bracket on the top. If you need a little more height, the # CE10002G-4 will be much the same, but measure 13 inches. The swivel bracket on the top pf these will let you angle your bunk boards to the angle that suits your needs best.
  view full answer...
• Roller Bunk Recommendation For Boat Trailer Used In Saltwater
  If you are looking to replace the bunks on your trailer with roller bunks, we have a few that may work for you. For a 5 foot bunk I recommend the CE Smith Roller Bunks, part # CE27710. These are constructed of 12 gauge galvanized steel and are rust and corrosion resistant. Since you said you are needing them for salt water, we recommend rinsing them with fresh water to prolong the life of the rollers. If you need a 4 foot version of these rollers I recommend part # CE27700. To...
  view full answer...

Do you have a question about this Boat Trailer Part?