Will CE Smith bolster Brackets for Pontoon Boat Trailers Fit Any Trailer
Updated 03/04/2025 | Published 07/12/2013
Question:
Will these work on all trailers?
asked by: Karl
0
Expert Reply:
The end to end span of the CE Smith Bolster Bracket # CE10052-32G for Pontoon Boat Trailers is 15.03 inches, which, according to CE Smith is the most important measurement when talking about pontoon trailer brackets.
CE Smith cannot guarantee these brackets will fit every trailer, however, they are widely used. In the picture you will see all of the dimensions listed so you can check your measurement needs against this bracket.
expert reply by:
Lori W
0
click to enlarge
Product Page this Question was Asked From
CE Smith Bolster Bracket for Pontoon Boat Trailers - Galvanized Steel - Qty 1
- Boat Trailer Parts
- Bunks
- Bolster Bracket
- Galvanized Steel
- CE Smith
more information >
Continue Researching
- Shop: CE Smith Bolster Bracket for Pontoon Boat Trailers - Galvanized Steel - Qty 1
- Search Results: trailer hitch extender
- Search Results: 36" hitch extension
- Search Results: 2" hitch extender
- Search Results: trailer extension
- Search Results: superhitch extension
- Q&A: Hole Spacing on Redline # 117521-G U-bolt Plate
- Search Results: roller bunks
- Shop: U-Bolt Plate for 2-1/2" Diameter, Round Trailer Axles with 2" Wide Springs
- Search Results: bunk mount
- Shop: etrailer Anti-Rattle Hitch Collar for 2.5" Hitch Receivers
- Shop: Kenda Karrier KR53 ST175/80R13 Radial Trailer Tire with 13" Silver Mod Wheel - 5 on 4-1/2
- Q&A: Type of Metal & Thickness of Curt Tubing with 2" Trailer Hitch Receiver
- Shop: Trailer Hitch Extender for 2" Hitch Receivers - 18" Long
- Shop: Curt Hitch Extension and Reducer for 2-1/2" Trailer Hitches - 24" to 34" Long
- Video: What to Know About the Buyers Products Black Receiver Tube 2" I.D. x 36" Long
- Video: An In-Depth Look at the Hitch Extender for Brophy Hitch-Mounted Stairs
- Video: Ultimate Overview of the Curt Hitch Extension and Reducer for 2-1/2" Trailer Hitches
- Video: Redline Trailer Suspension 117858 Review
- Shop: CE Smith Roller Bunks for Boat Trailers - 6 Rollers Each - 5' Long - 1,500 lbs - 1 Pair
- Video: Review of Tie Down Spare Tire Mount - Tongue Mount - TD98FR
- Video: In-Depth Review of the CE Smith Bolster Bracket for Pontoon Boat Trailers
- Q&A: Will the CE Smith Bolster and Swivel Bracket Assemblies CE10000G-4 Work on a Tritoon Trailer?
- Video: Replacement Roller for Dutton Lainson Roller Bunks: The Breakdown
- Q&A: Adding Bunks to 20 Foot Boat Trailer with Deep V Hull
- Q&A: How Would Roller Bunks Install on Karavan Boat Trailer
- Q&A: How To Determine Correct Bunk Boards and Mounting Hardware For 17' V Bottom Boat
- Q&A: Recommended Bunk Slicks That Can Be Attached Directly to the Lumber Bunks w/out Carpet
- Article: Boat Trailer Guides: Which are the Best?
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
Explore Expert Info
![Our Expert]()
on Boat Trailer Parts
on Boat Trailer Parts
Duane
3/4/2025
I sent a message several minutes ago asking about the Wing angle. It seems most are 130 degrees. My application requires 150 degrees. After seeing your dims, I tested my nearly forgotten Trig and came up with only 100 degrees for your part CE10052.326. Can you accommodate 6 to 9 parts at 150 degrees? TIA, Duane