Junction Box Replacement Recommendation for Trailer that Uses Cap Connectors for Trailer Wiring

Question

Question:

Hi I just wired in a new 7 pin cord to my campers front junction box. I am really not happy with what I see in that box. In particular, all of the wire nuts which are typical in these JB. Would this 10 pole box be a good replacement for that? I certainly understand my 7 wire connections just not sure how to manage the others. Im going to add a few pics to hopefully be of help. Thanks for any help.

asked by: Mike D

1

Helpful Expert Reply:

Cap connectors are not the best way to connect wires. The Pollak 10-Terminal Junction Box # PK52248 would be a way better way to make the connections as opposed to what you have now.

I attached a picture that shows the junction box wired up next to the picture you submitted to show the difference. I also attached an install video link for this as well.

expert reply by: Jameson C

1

click to enlarge

Answer 1

I have a solution for you, but there is not a plug-in adapter to convert your RV's taillights from combined wiring to separate wiring. If you are pulling a trailer with separate lighting, you will want to use a 2-wire to 3-wire converter. I…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Junction Box Replacement Recommendation for Trailer that Uses Cap Connectors for Trailer Wiring

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching