Install Video for Trailer Spindle Castle Nut

Question

Question:

Looking for the link to watch video of axle nut torque by “feel”. Thanks!

asked by: Mason

0

Expert Reply:

I believe I found the video you are referring to and have attached it below. You will want to fast forward to the 4:45 mark to see the spindle castle nut procedure.

As you mentioned you will basically just want to tighten the nut until it stops by itself. You don't want to actually torque it down to any specific spec. I have attached a link that will also take you to our available selection of spindle castle nuts that you can look through if needed.

expert reply by: Chris R

0

Jennifer

11/10/2025

Could I have the same link

Chris R.

11/10/2025

@Jennifer Of course! It's link further down on the page and I've also added it right below this comment. Just let me know if you need anything else!

Helpful Links

tv-faq-inspecting-hub-and-bearings.aspx

Answer 1

Since you are exceeding the trailer's gross vehicle weight rating (GVWR), the braking power is surely to be compromised. I would first recommend increasing the gain on your vehicle's brake controller. This will help to increase the braking…

view full answer...

Answer 2

According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement for…

view full answer...

Answer 3

The difference between the standard and EZ hubs is in the grease cap. For instance, the Trailer Hub and Drum Assembly - 3,500-lb E-Z Lube Axles #AKHD-545-35-EZ-K is the same hub, bearings, seal, and races as found in #AKHD-545-35-K but the grease cap…

view full answer...

Answer 4

The #BK2-100 Bearing Kit for #84 Spindle L44649/L68149 Bearings 10-19 Double Lip Seal will work. You have EZ Lube spindles which do not use a cotter pin. The spindle has a tube in it for the grease to be pumped in. Instead it uses a tang washer,…

view full answer...

Answer 5

If you only have the nut and a washer but no cotter pin or retaining type washer on the end then that isn't correct and you want to get a piece to help prevent that nut from backing off. If you have a setup like the Spindle Nut Kit for EZ Lube…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Install Video for Trailer Spindle Castle Nut

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching