What Size Clamp to Use for 3/8" and 1/2" Size Wire Loom

Question

Question:

What diameter R-Clamp do I use on 3/8inch loom? How about 1/2inch loom?

asked by: Charles D

1

Helpful Expert Reply:

You should be able to use the same size clip as the inner diameter of the wire loom. For example, the 3/8" Diameter Wire Loom # 39035 has grooves in it that would allow you to use a 3/8" inner diameter clamp. Same thing goes for the 1/2" Wire Loom # 459075-1 or # 459075.

expert reply by: Jon G

1

Answer 1

Yes, the Metal Loom Clamp part #A0500 will work on a trailer frame that is 5/16" thick. The Metal Loom Clamp will actually work on pretty much any frame thickness but you will need to make note of the size screw used. I recommend the Hex Screw…

view full answer...

Answer 2

I produced a short video showing how the Wire Frame Clip works on a piece of angle iron. The Principal is the same on a trailer frame and the clip will adhere better to the frame of the trailer because the steel will be thicker. It clips to the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

What Size Clamp to Use for 3/8" and 1/2" Size Wire Loom

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching